Acquisitions BLOOMSBURY SE 8kW Installation & User'S Instructions Download | Manualshive

Page: 6 / 16

background image

Page 6

AB-8kW-I03-191213

A flue stabiliser can be fitted to reduce the draught through the stove if the flue draught
is too high. The flue stabiliser should be:



Fitted in the same room as the stove.



The same size as the flue pipe.



Fitted no closer than 700mm to the flue outlet of the appliance.

DIMENSIONS & CLEARANCES

Fig.3 – Stove Dimensions

INSTALLING THE STOVE

«
...
4
5
6
7
8
...
»

Summary of Contents for BLOOMSBURY SE 8kW

















Reviews:

No comments

Related manuals for BLOOMSBURY SE 8kW

Brand: wiking Pages: 24

Brand: Yunca Gas Pages: 19

Brand: Primus Pages: 6

Brand: Dometic Pages: 288

Brand: Gasmate Pages: 2

Brand: Harbor Freight Tools Pages: 8

Brand: Charnwood Pages: 17

Brand: Charnwood Pages: 20

Brand: Charnwood Pages: 24

Brand: Charnwood Pages: 24

Brand: Travis Industries Pages: 42

Brand: Travis Industries Pages: 48

ECOFIRE ALLEGRO V1

Brand: Palazzetti Pages: 12

Ecofire Anita 7

Brand: Palazzetti Pages: 12

Brand: IronStrike Pages: 38

Brand: Heta Pages: 18

HR 160 SNELLA PLUS

Brand: Ravelli Pages: 188

Brand: Harrie Leenders Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands