background image

JR Data Loggers

10

Copyright © 2010 ACR Systems Inc.  All Rights Reserved.

To set when the logger will start recording click on the Start Time field.  Next, click on the

small button that appears at the right.  This will pop up a form allowing you to set the date and

time.  Highlight the date or time and enter the appropriate value.  You can also click on the

drop-down list arrow to bring up a calendar.  You can set the logger's starting time for just

over 65535*8 seconds (6 days, 1 hour, 38 minutes) ahead of the current time.  Note that the

start time will default to the closest time sampling within 8 seconds of the selected time.

1.2.2

Logger Channels

The Channels section indicates provides information specific to the channel.  The channel on

the logger is always enabled and continually recording readings and storing them in the

logger's memory.  The Channel subsections are 

Channel Information

 and 

Channel Calibration

.

1.2.2.1

Channel Information

When you contact the logger, the logger status is displayed.  The Channel line gives the

description and the Realtime value, if Realtime is turned on.  The Description field is editable. 

The Realtime value is based on the equation that you select for the channel.  The equation is

selected in the Setup window but is not shown in the Status window.    

Summary of Contents for JR-1000



























Reviews: