background image

 9 

 

 

 

 

      7– Operation Of Machine  

Machine includes a 3 kw electric motor. Firstly measure the currents coming to plug you will use before 
connecting  your  machine  to  plug  and  operating  it.  It  must  be  380  V  between  the  phases  and  220  V 
between  phase-neutral.  If  alternating  current  is  reaching  to  system,  it  will  damage  electrical  system  of 
your machine. In this situation, use a regulator to balance phases before operating the machine. 

WARNING! Otherwise electric faults which may occur will not be in scope of guarantee.  

Electric installation has phase protection relay. So that when phase with reverse order reaches to electric 
motor, phase protection relay activates and prevents the reverse operation of electric motor and hydraulic 
pump which is connected to motor from working in reverse direction, and protects the system. (See Picture 
2)  In  such  a  situation  if  the  machine  is  not  working,  remove  machine's  three-phase  electric  cable  and 
connect to another suitable three-phase socket. When the phase coming to motor is correct, system will 
activate. 

To start the machine open pacco switch on unit and press on motor start button (green button) after 
waiting for 5 seconds. (See Picture 3) And hydraulic system will become activate 

MOTOR 

STOP 

MOTOR 

START 

PACCO 

SWITCH 

Picture –3

 

When the lamp is off 

 

REVERSE PHASE 

When the lamp is 0n  

 

FLAT PHASE 

Picture –2

 

Summary of Contents for M24



















Reviews: