SERIES IP330 INDUSTRIAL I/O PACK 16-BIT HIGH DENSITY ANALOG INPUT MODULE
___________________________________________________________________________________________
- 22 -
TERMINATION PANEL: MODEL 5025-552
Type: Termination Panel For AVME9630/9660 Boards
Application: To connect field I/O signals to the Industrial I/O
Pack (IP).
Termination Panel:
Acromag Part 4001-040
(Phoenix Contact Type FLKM 50). The 5025-552 termination
panel facilitates the connection of up to 50 field I/O signals and
connects to the AVME9630/9660 3U/6U non-intelligent carrier
boards (A-D connectors only) via a flat ribbon cable (Model
5025-551-x). The A-D connectors on the carrier board
connect the field I/O signals to the P2 connector on each of
the Industrial I/O Pack modules. Field signals are accessed
via screw terminal strips. The terminal strip markings on the
termination panel (1-50) correspond to P2 (pins 1-50) on the
Industrial I/O Pack (IP). Each Industrial I/O Pack (IP) has its
own unique P2 pin assignments. Refer to the IP module
manual for correct wiring connections to the termination panel.
Schematic and Physical Attributes: See Drawing 4501-464.
Field Wiring: 50-position terminal blocks with screw clamps. Wire
range 12 to 26 AWG.
Connections to AVME9630/9660: P1, 50-pin male header with
strain relief ejectors. Use Acromag 5025-551-x cable to
connect panel to VME board. Keep cable as short as
possible to reduce noise and power loss.
Mounting: Termination panel is snapped on the DIN mounting rail.
Printed Circuit Board: Military grade FR-4 epoxy glass circuit
board, 0.063 inches thick.
Operating Temperature: -40
°
C to +100
°
C.
Storage Temperature: -40
°
C to +100
°
C.
Shipping Weight
: 1.25 pounds (0.6kg) packaged.
TERMINATION PANEL: MODEL 5029-910
Type: Screw-Terminal Termination Panel For Acromag APC8600
PC/AT ISA bus Carrier Boards.
Application: This panel converts the high-density ribbon-cable
connectors coming from the APC8600 carrier board to screw
terminals, for direct-wired interfaces. This panel facilitates the
connection of up to 50 field I/O signals and connects to the
APC8600 PC/AT ISA bus carrier board via high-density (25-mil
pitch) flat ribbon cable and connectors. The A & B connectors
on the carrier board connect the field I/O signals to the P2
connector on each of the Industrial I/O Pack modules. Field
signals are accessed via screw terminal strips. Each Industrial
I/O Pack (IP) has its own unique P2 pin assignments. Refer to
the IP module manual for correct wiring connections to the
termination panel.
Field Wiring: 50-position terminal blocks with screw clamps. Wire
range 12 to 26 AWG.
Connections to APC8600: P1, 50-pin, high-density male header
with strain relief.
Mounting: Termination Panel includes mounting holes.
Printed Circuit Board: Military grade FR-4 epoxy glass circuit
board, 0.063 inches thick.
Operating Temperature: -40
°
C to +85
°
C.
Storage Temperature: -55
°
C to +125
°
C.
Shipping Weight: 1.25 pounds (0.6kg) packaged.
TRANSITION MODULE: MODEL TRANS-GP
Type: Transition module for AVME9630/9660 boards.
Application: To repeat field I/O signals of IP modules A through D
for rear exit from VME card cages. This module is available
for use in card cages which provide rear exit for I/O
connections via transition modules (transition modules can
only be used in card cages specifically designed for them). It
is a double-height (6U), single-slot module with front panel
hardware adhering to the VMEbus mechanical dimensions,
except for shorter printed circuit board depth. Connects to
Acromag termination panel 5025-552 from the rear of the card
cage, and to AVME9630/9660 boards within card cage, via flat
50-pin ribbon cable (cable Model 5025-551-X).
Schematic and Physical Attributes: See Drawing 4501-465.
Field Wiring: 100-pin header (male) connectors (3M 3433-D303 or
equivalent) employing long ejector latches and 30 micron gold
in the mating area (per MIL-G-45204, Type II, Grade C).
Connects to Acromag termination panel 5025-552 from the
rear of the card cage via flat 50-pin ribbon cable (cable Model
5025-551-X).
Connections to AVME9630/9660: 50-pin header (male) connectors
(3M 3433-1302 or equivalent) employing long ejector latches
and 30 micron gold in the mating area (per MIL-G-45204, Type
II, Grade C). Connects to AVME9630/9660 boards within the
card cage via flat 50-pin ribbon cable (cable Model 5025-551-
X).
Mounting: Transition module is inserted into a 6U-size, single-
width slot at the rear of the VMEbus card cage.
Printed Circuit Board: Six-layer, military-grade FR-4 epoxy glass
circuit board, 0.063 inches thick.
Operating Temperature: -40
°
C to +85
°
C.
Storage Temperature: -55
°
C to +105
°
C.
Shipping Weight: 1.25 pounds (0.6Kg) packaged.
