7
Algunos modelos (ver Pag. 2) cuentan con quemador programable.
El quemador programable es un quemador que funciona según el
tiempo que se le programe en el reloj desde 1:59 horas hasta 1
minuto. Este quemador se localiza en la parte frontal derecha de la
estufa.
Para operar el quemador programable:
1.- Pulse la tecla (Quemador Programable) del reloj, ajuste
el tiempo que desea mantener encendido el quemador, hasta
1:59 horas oprimiendo la tecla ó 0:59 minutos o menos
oprimiendo la tecla .
2.- Encienda el quemador programable oprimiendo la perilla y girándola
hasta la posición de flama máxima, mantengala oprimida por 3
ó 4 segundos hasta que el quemador encienda, una vez encendido,
mantenga la perilla presionada hasta que el quemador permanezca
encendido cuando libere la perilla, (Aprox. 10 segundos).
3.- Cuando el tiempo del TIMER llegue a cero, el quemador se
apagará automáticamente y sonará indicando que el tiempo se
ha terminado.
4.- Al apagarse el quemador, la válvula quedará en posición de
abierto, el gas no se fugará debido al dispositivo de seguridad,
regrese la válvula a la posición de apagado.
EN TIEMPO
(QUEMADOR PROGRAMABLE)
Para encender los quemadores superiores con encendido electrónico
independiente:
Algunos modelos (ver Pag. 2) cuentan con
encendido electrónico independiente, para
operarlo oprima el botón que se localiza en el
lado izquierdo del frente de perillas y al
mismo tiempo presione y gire 1/4 de vuelta la
perilla del quemador que desea encender.
ENCENDIDO ELECTRÓNICO DE QUEMADORES SUPERIORES
1.- Algunos modelos (ver Pag. 2) cuentan con encendido
electrónico en la perilla, para operarlo gire la perilla
del quemador que desea encender hasta la posición
de encendido, (ver figura).
2.- Para que la bujía de encendido deje de producir
chispas, gire la perilla hasta la posición de flama
máxima.
Perilla en posición de encendido.
Para encender los quemadores superiores con encendido electrónico
integrado en la perilla:
Some models (see page 2) include a programmable burner.
The programmable
burner operates
with the
timer, with
a
range from 1:59 hours to 1 minute. The burner is located in
the right front side of the range.
How to operate the programmable burner:
1.- Push the button, adjust the hour with the button,
adjust the minutes with the button. The time showing,
up to 1 hour and 59 minutes, is how long the burner will
run.
2.- Tu
rn on
the programmable
burner, push
the knob
and
turn it to the ignition mark, continue pushing the knob for
3 t
o 4
seconds
until the
burner lights,
press the
knob
some
more seconds
until the
burner remains
on.
(Aprox. 10 seconds).
3.- When
the programmed
time is
over, the
burner will
turn
off
automatically
and the
beeper will
sound.
4.- When
the burner
turns of
f, the
valve will
remain open,
but
the
gas
will not
leak
due to
the
safety device,
turn
the
valve to off position.
7
To turn on the surface burners with independent
electronic ignition:
Some models (see page 2) have independent
electronic ignition, to operate it push the button
located on the left side of the manifold panel while
you push and turn the desired knob. Release the
ignition button when the burner lights.
PROGRAMMABLE BURNER
TOP BURNERS WITH ELECTRONIC IGNITION
To turn on the surface burners with electronic
ignition in the knob:
1.- Some models (see page 2) have electronic ignition
integrated in knobs, to operate push and turn the
desired knob to the ignition position. (See illustration).
2.- To stop the sparks turn the knob to the
maximum flame position.
Knob on
the mark
of ignition.
Quemador Programable
Perilla en posición de encendido.
APAGADO
FLAMA
MÍNIMA
FLAMA
MÁXIMA
BOTÓN DE ENC.
ELECTRÓNICO
Knob in
ignition position.
OFF
MINIMUM
FLAME
MAXIMUM
FLAME
ELECTRONIC IGNITION
BUTTON
APAGADO
FLAMA
MÍNIMA
FLAMA
MÁXIMA
OFF
MINIMUM
FLAME
MAXIMUM
FLAME
Programmable Burner