background image

Compact FLASH III Digital Audio System 

Copyright©1992-2007 by ACS, Sarasota, Florida 

20 

ALL RIGHTS RESERVED  

Diagnostic LED Codes (Red & Green LEDs) 

Green LED 

 

Flashes three times a second while scanning or loading CF Card files. 

 

Steady on when loaded, ready or playing in CFSound mode.

 

 

Flashes once a second while running ACS Basic mode

  

Red LED Error Flashes 

The Red LED can indicate up to 4 error conditions by flashing 1 to 4 unique numeric code patterns from 
the following table in a continuously repeating sequence. The Red LED flashes at three times a second for 
the value of the pattern, followed by a half second gap, then the next pattern. 

Flash Count  Error Condition 

One  Problem w/ATA interface, non-compatible CF card, bad CF card, execution stops. 

Two  Error opening .WAV file for that input, incorrect filename, file does not exist. 

Three 

 

Error when reading file, file corrupted, unsupported file type, the sound doesn t start or 
stops playing. 

Four 

 

No valid  *.WAV  files of a CFSound Mode Filename Format found on the CF Card 

 

starting ACS Basic. This code will continue until a Basic RUN command is issued.

 

Five 

 

No valid FAT or FAT32 file system found on the CF Card, execution stops.

 

Six 

 

Error seeking within file when starting or resuming sound, the sound doesn t start or 
resume.

 

Seven  Error initializing CODEC, execution stops. 

Eight  Invalid .WAV file internal structure, file is ignored. 

Nine  Unsupported .WAV format (not Windows PCM), file is ignored. 

Ten  Unsupported .WAV sample rate (not 44.1KHz), file is ignored. 

Eleven  Unsupported .WAV sample size (not 16-bit), file is ignored. 

Twelve 

Contact closure without matching sound file, a contact closure with matching sound file 
stops this code from flashing. 

Thirteen  Speaker is muted by RS-232 command or ACS Basic command. 

  

Power Requirements 

The  idle  current  of  a  CFSound  III  unit  with  an  8MB  Kingston  CF  card  installed  is  ~170mA  @  12VDC 
input.  

With  a  background  sound  playing  at  a  moderate  level,  the  current  consumption  averages  ~250mA  @ 
12VDC. 

Summary of Contents for Compact FLASH III






































Reviews: