background image

16 

  Open zone valves manually using the solenoid manual lever.  If flow is restored, 

go  back  to  the  BDMC  and  check  connections  again  and  then  trace  the  wiring 
back to the solenoid.   

  Check  piping  connections  and  verify  that  pressure  is  present  in  the  field.    This 

could indicate that the drippers are plugged. 

 
Your 

“ACT WFS”  dealer can provide additional advice  should  the above methods fail.  

Be sure to have completed all of the above service and testing prior to calling.  
 
 

Manufacturer: 

 

JNM Technologies, Inc 
PO BOX 5667 
Bryan, TX  77805-5667 

 

979-779-6500 
979-779-65505 fax 

 

Appendices: 

 

System Drawings for ACT 100S, C200S and C400S 
 
 

LIMITED WARRANTY/LIMITATION OF BUYER’S REMEDIES 

 

(A) BASIC MANUFACTURER’S LIMITED WARRANTY: 

Except as to products described in Subsections (B), (C), (D), and (E) below, products sold and/or 
manufactured by JNM Technologies, Inc., are warranted to be free from original defects in material and workmanship 
for a period of one (1) year from the date of delivery to the buyer unless (i) otherwise specified by and subject to the 
terms and conditions of any Warranty Supplements pertaining to specific products or, (ii) expressly disclaimed in 
writing by JNM Technologies, Inc.. Within the warranty period, JNM Technologies, Inc. at its sole discretion shall have 
the option to repair or replace part or all of a defective product, or refund part or all of the original purchase price, if 
any part proves to be defective in material or workmanship after ret

urn of such product at customer’s expense and 

after such return has been authorized in writing by JNM Technologies, Inc.. THIS BASIC MANUFACTURER’S 
LIMITED WARRANTY IS SUBJECT TO THE TERMS AND PROVISIONS IN SUBSECTION (F), (LIMITATION OF 
REMEDIES AND DISCLAIMER OF WARRANTIES) SET FORTH BELOW IN THE EVENT OF ANY 
INCONSISTENCY BETWEEN SUBSECTION (A) AND SUBSECTION (F) OF THIS PRODUCT WARRANTY, THE 
PROVISIONS OF SUBSECTION (F) SHALL PREVAIL. 
 

(B) DRIPPERLINES: 

Bioline dripperlines are warranted to be free from original defects in materials and workmanship for a period of five (5) 
years and seven (7) years for environmental stress cracking. Further, the Bioline warranty against emitter clogging 
due to root intrusion will be for a period of ten (10) years. This warranty shall apply only to products with a wall 
thickness of 35 mil or greater. 
 

(C) FILTERS: 

Disc filters are warranted to be free from original defects in materials and workmanship for a period of five (5) years. 
This warranty specifically excludes gaskets, seals and o-rings, which are subject to the basic one (1) year warranty. 
 

(D) VALVES: 

Valve bodies are warranted to be free from original defects in materials and workmanship for a period of five 
(5) years. Valve diaphragms are warranted for a period of two (2) years. 
 

(E) AIR VENTS: 

Summary of Contents for ACT-100S



















Reviews: