background image

17 

Air vent bodies are warranted to be free from original defects in materials and workmanship for a period of five (5) 
years. Polypropylene air vent bodies are warranted for two (2) years. This warranty specifically excludes internal 
seals, gaskets or o-rings which are subject to the basic one (1) year warranty. 
 
 

Product Description Warranty Length 

 
AIR VENT BODIES 5 years 

Gaskets, Seals, 0-Rings 1 year 
Polypropylene Bodies 2 years 

CHECK VALVES 1 year 
DISC FILTERS 5 years 

Gaskets, Seals, 0-Rings 1 year 

 
BIOLINE DRIPPERLINE 5 years 

Env. Stress Cracking 35 mil/greater 7 years 
Emitter Clogging due to Root Intrusion 10 years 

FITTINGS 1 year 
FLOW METERS 1 year 
HYDROMETERS 1 year 
PRESSURE REGULATORS 1 year 
VALVES 

Bodies 5 years 
Diaphragms 2 years 

ALL PRODUCTS NOT LISTED 1 year 
 

PRODUCT WARRANTY 

 

 (F) LIMITATION OF REMEDIES AND DISCLAIMER OF WARRANTIES 

EXCEPT AS EXPRESSLY PROVIDED HEREIN, ALL WARRANTIES EXPRESSED OR IMPLIED, INCLUDING 
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, 
ARE HEREBY EXCLUDED AND DISCLAIMED. 
THE REMEDIES PROVIDED HEREIN SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF THE BUYER. 
NO OTHER EXPRESS WARRANTY IS GIVEN AND NO AFFIRMATION BY JNM TECHNOLOGIES, INC., BY 
WORDS OR ACTION, WILL CONSTITUTE A WARRANTY. 

NO 

OTHER EXPRESS WARRANTY NOR ANY OTHER 

REMEDY SHALL BE AVAILABLE TO THE BUYER AND JNM TECHNOLOGIES, INC. SHALL NOT BE 
RESPONSIBLE OR LIABLE FOR ANY DAMAGES, INCLUDING ANY LOSS OF PROFIT, LOST SAVINGS, LOSS 
OF SALES, OR OTHER DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, INJURY 
OR DAMAGES TO ANY PERSON OR PROPERTY ARISING OUT OF THE USE OR INABILITY TO USE THE 
PRODUCTS OR THE BREACH OF ANY EXPRESS WARRANTY, EVEN IF JNM TECHNOLOGIES, INC. HAS 
BEEN ADVISED OF THE POSSIBILITY OF THOSE DAMAGES OR CLAIMS. JNM TECHNOLOGIES, INC. SHALL 
NOT BE RESPONSIBLE FOR THE AFORESAID DAMAGES, CLAIMS OR LOSSES DUE TO LATE DELIVERY OR 
DELIVERY OR NON-DELIVER, OR OTHERWISE. THERE ARE NO WARRANTIES WHICH EXTEND 
BEYOND THE DESCRIPTION AS SET FORTH HEREIN. IF JNM TECHNOLOGIES, INC SHALL FURNISH 
TECHNICAL ADVICE OR ASSISTANCE WITH RESPECT TO THE PRODUCTS SOLD HEREUNDER, IT SHALL BE 
GIVEN WITHOUT CHARGE TO BUYER AND SHALL BE GIVEN AND ACCEPTED AT BUYER’S SOLE RISK 
WITHOUT ANY EXPRESS OR IMPLIED WARRANTY AND JNM TECHNOLOGIES, INC. SHALL NOT BE 
RESPONSIBLE OR LIABLE FOR THE ADVICE OR THE RESULTS THEREOF BUYER ASSUMES ALL RISK AND 
LIABILITY RESULTING FROM USE OF THE PRODUCT PURCHASED. 
 
This warranty is expressly conditioned upon proper storage, installation, application and normal 
wastewater use and service as recommended by JNM Technologies, Inc.. Such recommendations may be 
updated from time to time. Any misuse, neglect, modifications, unauthorized repairs or replacement or uses 
of the product and/or any of its components for purposes not recommended by JNM Technologies, Inc., including but 
not limited to the following, shall completely void this warranty: 
(I) Water which has not been filtered or treated to the levels specified for individual components of the 
product by JNM Technologies, Inc.. 
(II) Chemical concentrates, used or applied internally or externally to the product, or mechanical abuse 
which is harmful to the product or its components. 
(III) Operating pressures greater than those speci

fied by JNM Technologies, Inc.’s individual component 

specifications. 
(IV) Damage or plugging caused by insects, rodents, other animals, improper installation or other 
mechanical damage. 
THE EXPRESS WARRANTY PROVIDED HEREIN IS EFFECTIVE ONLY IF CLAIM IS MADE BY WRITTEN NOTICE 
WITHIN THE APPLICABLE WARRANTY PERIOD AND POSTMARKED WITHIN THIRTY (30) DAYS AFTER 
DISCOVERY OF THE DEFECT ON WHICH THE CLAIM IS BASED. SUCH NOTICE SHALL BE DELIVERED TO 
JNM TECHNOLOGIES, INC. AT THE FOLLOWING ADDRESS: 

Summary of Contents for ACT-100S



















Reviews: