background image

www.acti.com

  Hardware Manual 

21 

 

How to Connect DI/DO and Audio Devices (Optional) 

Depending on your surveillance needs, you may connect digital input / output or audio input / 

output devices to your camera. The camera comes with one (1) terminal block for both digital and 

audio input/output devices. 

 

How to Connect DI/DO Devices 

Digital Input (DI) devices can be used to notify the camera about an activity in the camera site. DI 

can be triggers of events. For example, you can connect a “panic button” to the camera; as such 

when the panic button is pressed, the alarm signal will be sent through the camera. Other 

common DI device applications are emergency button, smoke detector, passive infrared sensor, 

etc. 

Digital Output (DO) devices are external devices that are activated by the camera upon an event 

inside the camera. For example, you can connect an “alarm horn” to the camera; as such when 

an event occurs inside the camera (e.g. detected intruder), the alarm horn will sound. Other 

common DO device applications are motion-triggered lights, electric fence, magnetic door locks, 

etc. 

Press and hold the orange tab as you insert the wire through the pin slot, then release the orange 

tab to secure the wire. 

     

 

To connect digital input / output devices (DI/DO), map the pins to one of the pin combinations 

below: 

 

Device 

Pin 

Mapping Instructions 

Digital Output (DO) 

12V 

Connect the wires of the output device to   

12V

 and 

DO

DO 

Digital Input (DI) 

GND 

Connect the wires of the input device to 

GND

 and 

DI

DI 

 

 

 

For DI/DO Use 

Summary of Contents for E213



































Reviews: