background image

www.acti.com

 
 

Hardware Manual 

               

Physical Description 

 

Item 

Description 

Lens 

Provides a wide viewing angle   

Speaker 

The built-in speaker allows the user to hear the person on the 

receiving end. 

Push Button 

Functions as the emergency button. Push to notify and speak to 

personnel in charge.   

Built-in Microphone 

The built-in microphone allows the user to speak to the person on 

the receiving end. 

Audio Input / 

Digital Input / 

Serial Connector 

Connects external input devices such as audio and digital input 

devices. Serial devices that use RS-485 protocol can also be 

connected here. See 

Cable Connections

 on page 11. 

Power LED 

Lights red when the camera is powered up. 

Memory Card Slot 

 

 

Insert a memory card (not included) into the slot for local recording 

purposes. See 

How to Install / Remove the Memory Card

 on 

page 14 for more information. 

NOTE:

 Supports only microSDHC and microSDXC cards. 

Ethernet Port 

Connects to a network using an Ethernet cable. 

9

 

 

Reset Button 

Restores the factory default settings of the camera. To reset the 

camera, while the power is on, press and hold the Reset Button for 

at least 5 seconds or until the Power LED goes off. 

10 

Digital Output 

Connects to digital output devices, such as an alarm trigger, etc. 

See 

Cable Connections

 on page 11 for information. 

Summary of Contents for Q970






















Reviews: