background image

www.acti.com

U

SER’S MANUAL 

 

EU Conformity Statement 

 

This product and - if applicable - the supplied accessories too are 

marked with "CE" and comply therefore with the applicable 

harmonized European standards listed under the EMC Directive 

2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 

2011/65/EU 

 

2012/19/EU (WEEE directive): Products marked with this symbol 

cannot be disposed of as unsorted municipal waste in the European 

Union. For proper recycling, return this product to your local supplier 

upon the purchase of equivalent new equipment, or dispose of it at 

designated collection points. For more information see: 

www.recyclethis.info 

 

2006/66/EC (battery directive): This product contains a battery that 

cannot be disposed of as unsorted municipal waste in the European 

Union. See the product documentation for specific battery 

information. The battery is marked with this symbol, which may 

include lettering to indicate cadmium (Cd), lead (Pb), or mercury 

(Hg). For proper recycling, return the battery to your supplier or to a 

designated collection point. For more information 

see:www.recyclethis.info 

 

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject 

to the following two conditions:   

(1) this device may not cause interference, and 

(2) this device must accept any interference, including interference that may cause undesired 

operation of the device. 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils 

radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 

(1) l'appareil ne doit pas produire de brouillage, et 

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le 

brouillage est susceptible d'en compromettre le fonctionnement. 

 

 

Summary of Contents for R72FT-31






















Reviews: