background image

15

S002025 Action 4 Unit Swing Set

Warranty Information (cont)

The service centre representative will assess the claim. If:

1) 

there is a minor fault

, they can offer either a replacement spare part, replacement unit, repair or 

other suitable remedy.

2) 

there is a major fault

, they can offer a replacement, repair or suggest you return to the store you 

purchased it from for a full refund.

Please note: 

a request for compensation will need documentary evidence of the loss or damage 

suffered. It will also need to be evidenced that such a loss was a reasonably foreseeable result of a 
failure to comply with a consumer guarantee under the Australian Consumer Law.

3) 

The product was damaged through abnormal use

, no refund or repair can be offered.

The sending of replacements, spare parts or the cost of repair carried out will be organized and covered 
by the Service Centre. If collection of the item is required this will be organized by the Service Centre and 
at our expense. Do not return any products without authorization as this will be at your expense.

Our sales and service centre has been set up to provide assembly assistance, replacement parts and 
accessories, and to efficiently handle all warranty related matters. Please note upon receiving your 
warranty claim our Service Centre will send, via post or email, a repair and refurbished goods or parts 
notice.

SERVICE CENTRE

Contact details and hours of operation.
Freecall 1800 465 070

9:00am – 4:30pm Monday to Friday (excluding Public Holidays)
9:00am – 3:00pm Saturday

This product is warranted and distributed by:
Action Sports of 48B Egerton St, Silverwater NSW, 2128 
Phone: (02) 8799 3500

© 2017 Action Sports Equipment Pty Ltd.

Summary of Contents for S002025
















Reviews: