© Action Products, Inc. 2021 ACTION, AKTON, SHEAR SMART, TWISTER and XACT are registered trademarks of Action Products, Inc., USA
L0232-003
•
Do not soak product in any type of cleaning or disinfecting agent.
•
Do not autoclave or gas sterilize product as it will compromise product integrity.
•
Do not machine wash or machine dry pads.
Cleaning: Wheelchair Covers
•
If pad is encased in a clear film bag do not remove or damage the bag because it can expose the interior foam to contaminants that may
result in user harm or product deterioration.
•
Follow cleaning instructions printed on the cushion cover label. Always rinse with clear water to remove any cleaning residuals. For best
results ensure covers are thoroughly dried before replacing on the cushion.
•
Incontinent covers should be air-dried or towel-dried inside and out before replacing on cushion
•
Use care when removing and replacing cover on pad. Keep corners of film covering and edges of pad away from cover zipper.
•
Always ensure cover is properly fit to the cushion before placing it back in use.
o
For Xact® series wheelchair covers, align cover zipper with flat, bottom edge of cushion for proper fit.
o
For Xact® LP2 covers with clear windows, match cover windows to the green “Correct” labels on the cushion for proper fit.
Resurfacing:
•
If product is being used in a healthcare facility, consult your facility’s protocol for resurface or repair of any product.
•
Twister® Wheelchair Backs and products with foam are not recommended for resurfacing. If damaged, we recommend the pad be
removed from use, discarded, and replaced immediately.
•
Polymer products may be resurfaced if they have minor cuts or light abrasions only. Product should not be resurfaced more than once.
Presence of tears, gouges, large cracks, bubbles, or excessively deep creases indicates a product should be removed from use, discarded,
and replaced.
•
Inspect any resurfaced product before each use to ensure the film resurfacing tape remains secure and clean. There should be no loose
edges or presence of debris.
Resurfacing Guidance
:
o
Clean and disinfect product according to this Guide prior to resurfacing the product.
o
If necessary, cut the film tape to proper size, allowing a 0.25 – 0.5” (0.6 – 1.3cm) border of film to ensure damaged area is fully
encased beneath the film.
o
Carefully peel back one half of release paper and crease it. Carefully adhere exposed portion of film tape to damaged surface,
pushing out any air bubbles that may become trapped beneath the film tape.
o
Continue to apply tape while slowly removing the release paper until film tape is firmly secured to the product surface.
o
Clean and disinfect the product before placing it back in use.
Twister® Back
Action recommends this product be installed by a trained individual. Product is designed to function as a 2-piece set. Pieces should not be used
individually. The hook and loop strap system designed to position the patient, is the component that attaches to the wheelchair cane posts. The
padded fabric overlay that is placed over the hook and loop strap system is designed to comfortably protect and support the user at the product
interface.
Inspect product at regular intervals to ensure:
•
Hook and loop strap system is properly attached to wheelchair cane posts.
•
Hook and loop strap system is properly attached to the padded fabric overlay component.
•
User is properly and comfortably positioned by installed product.
Installation and Adjustment:
•
Remove existing wheelchair back upholstery in manner best suited for the wheelchair style.
•
Install hook and loop strap system on existing wheelchair cane posts.
•
Reinstall screws into eyelets of the cane posts to securely affix the strap system to the wheelchair.
•
Increase or decrease tension of the hook and loop straps to the user’s comfort level and positioning requirements to achieve optimal fit
and performance.
•
Place padded overlay component of product over hook and loop strap system and secure vertical hook and loop strips on both front and
back of the overlay component to mated hook and loop strips of installed strap system.
•
Face the padded, ribbed fabric portion of the overlay towards the user/ front of the wheelchair to create an overlay to user interface.
•
Secure mated hook and loop strips at bottom of overlay and tuck bottom flap of overlay component beneath wheelchair cushion. Mated
hook strips are enclosed to place on wheelchair seat to additionally secure overlay component directly to the wheelchair.
•
Ensure hook and loop strap system is secured to overlay component. Regularly inspect straps to ensure they are properly secured.
Cleaning: Twister® Back
•
Fabric covering of padded overlay component and strap system base may be lightly cleaned with a microfiber cloth dampened with a
solution of warm, soapy water. Always rinse with clear water to remove any cleaning residuals. Allow to air dry.
•
Do not machine wash, machine dry, or dry-clean this product.
