11
3
SET UP
Remove the Bouncer from the carry bag. Place the Bouncer on a level surface at least 2M from any
structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines or electrical
wires.
Check the ground where the Bouncer is to be inflated for any sharp objects or unusual by products. Do not
install the Bouncer over concrete, asphalt or any hard surface.
Set up away from water and any potential fire hazards.
Set up as near to power source as possible. After stretching the air fill tube, position the blower (air pump)
at the end of the tube. Push ground stakes for air blower through blower base holes firmly to the lawn
ground.(Refer to picture 1)
Slide the end of the tube around the blower (air pump) air blow sprout and tighten the string.
The air fill tube should be straight and untwisted. Reposition the blower (air pump) if necessary.
Make sure the blower (air pump) "on/off" switch is in the off position.
Plug the blower into an approved grounded outlet.
Keep the blower (air pump) and power cord away from water and moisture. If water contacts the blower (air
pump), unplug the blower (air pump) power cord. Do not operate until the blower is completely dry.
Ensure the blower (air pump) is free from debris and securely sited to avoid tripping. To inflate the bouncer
unit, (press the reset button on GFCI) turn the blower (air pump) "on/off" switch to on. The continual air-flow
blower (air pump) must be left on at all times while the Bouncer is being used.(Refer to picture 2)
If the product comes with water bags, like item #9082N, please follow the undermentioned instruction,
otherwise, overleap this point. Spread out the product, place and fasten the empty water bags at the two
sides of the product. Open the stopple and fill water in the water bags until 80% full (about 22kg), push and
close the stopple. Make sure water bags are firmly attached on the product and no water leakage before
the product is fully inflated, and never allow children to play on the slide without installing water bags.(Refer
to picture 3)
The Bouncer should take less than 2 minutes to inflate.
If the product comes with slide extension, like item #9082N, please follow the undermentioned instruction,
otherwise, overleap this point. Add the Slide extension to the end of the Slide using the Velcro fastener.
(Refer to picture 4)
Ground support stakes are used for lawn ground surfaces. Hook stakes over loops in the Bouncer. To
prevent overturn or lift during play, push stakes firmly into the soil. The stakes should be placed level with
or under the ground in order to reduce tripping hazards.(Refer to picture 5)
If the products comes with the following functions or accessories, please follow the below correspondence
points accordingly, otherwise, overleap the relevant functions points in the following, Put the
correspondence accessories into the product if provided, such as:
Supply the ball-ball pool with plastic balls provided. (Refer to picture 6)
Supply the dart board with dart balls provided. (Refer to picture 7)
You can toss some plastic rings (not provided) to have fun easily. (Refer to picture 8)
You can throw the plastic ball into the net to have fun easily. (Refer to picture 9)
You can play the plastic ball with the basketball hoop to have fun.(Refer to picture 10)
You can fasten the sun roof on the top of the product by velcro.(Refer to picture 11)
To prevent overturning during play, periodically check that the ground stakes are securely in place. To anchor
the product properly, ALWAYS anchor the product and blower with corresponding ground stakes before use.
Make sure the Bouncer is inflated fully and securely anchored before children enter to play.
Failure to do so will result in the product being unstable and can cause serious injuries. Use of this product
when under-inflated or during deflation could cause serious injuries.
Always check for excessive air loss, and re-inflate before allowing play to continue. As the product remains
inflated through constant air flow, air leakage from the seams is normal and necessary so the product does
not over inflate.
10
9
8
7
6
5
4
2
3
1
