background image

©2017 Actions Microelectronics Co., Ltd. All right reserved.  Quattro Pod or Quattro are trademarks of Actions 

Microelectronic Co., Ltd., registered in China and other countries. Other product and company names mentioned 

herein may be trademarks other respective companies. 

 

FCC STATEMENT  

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions:  

(1) This device may not cause harmful interference.  

(2) This device must accept any interference received, including interference that may cause 

undesired operation.  

2. Changes or modifications not expressly approved by the party responsible for compliance 

could void the user's authority to operate the equipment.  

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation.  

This equipment generates uses and can radiate radio frequency energy and, if not installed and 

used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following measures:  

Reorient or relocate the receiving antenna.  

Increase the separation between the equipment and receiver.  

 Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.  

 Consult the dealer or an experienced radio/TV technician for help. 

 

FCC Radiation Exposure Statement  

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with minimum distance 20cm 

between the radiator & your body 

 

 

本產品符合國家通訊傳撥委員會

(NCC)

之規範:

 

低功率電波輻射性電機管理辦法

 

第十二條

  

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻

率、加大功率或變更原設計之特性及功能。

   

第十四條

 

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應改善

至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須
忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

 

*您可以在官網下載到最新版完整手冊以及相關品問題:

www.iezvu.com

 

©2017 Actions Microelectronics Co., Ltd. : Quattro

 Quattro Pod

Actions Microelectronic 

Co., Ltd., 

炬力北方股份有限公司在大陸地區與其他國家註冊之商標,說明書中提到的相關產品

名稱或商標則屬於相對應之該公司

 

 

 

 

 

Distribution:

PureLink GmbH

Available from B2B Online Portal

Summary of Contents for QuattroPod




























Reviews: