Headless Mode Instructions
When synching, the antenna of the remote control must be aligned with the tail of the drone. In
normal fl ight, when pressing headless button, a beep and fl ashing guide light signifi es headless
mode. Press this button again to exit headless mode.
One Key Return
When the drone fl ies at a distance, the one key return button can recall the aircraft. Following device
connection, the antenna of the transmitter must be aligned with the tail of the craft in order to
takeoff. Press the one key return button to enter return mode, the light will fl ash. Press the button
again to exit return mode. When returning, the forward and backward movement of right lever can
interrupt this function.
High and Low Speed Switching
During fl ight, the fl ight speed can be adjusted by pressing this button while in any direction. The
craft’s default speed is low. Press this button once to switch to medium speed, the transmitter will
beep twice. Press the button again to switch to high speed, the transmitter will beep three times.
Press again to return to low speed.
360° Flip
Once familiar with basic operation, the aircraft can be fl own to a height of more than 3 meters, and
perform 360° Flip. To invert the craft, turn on the rear right side of the transmitter, then push the
right rudder (in any direction) to achieve a 360 degree fl ip.
OPERATION OF AUTOMATIC FUNCTIONS
Start the Drone
Method 1: Press One Key Takeoff Button once and the propeller will start spinning and the drone
will fl y up.
Method 2: Simultaneously push the left throttle control stick to the bottom left corner and the right
direction control stick to the bottom right corner for approximately 1 second and the propellers will
spin slowly.
Altitude Hover Function
Push the left throttle control stick upwards, then downwards and release. The craft will maintain that
height when released.
Turn Off the Drone
Method 1: Long press the emergency stop button, the propeller will stop working, locking the craft.
Method 2: Push the left throttle control stick down for 3 seconds, the blade will stop spinning.
One Key Take Off
Turn on drone, press the One Key Start the drone will propel upwards, and can be controlled to go
towards any desired direction once it is fl ying.
One Key Landing
When fl ying, press the One Key Landing the drone will descend, and can be controlled to land in a
desired location.
Emergency Stop
When the aircraft collides during the fl ight and cannot be controlled, the emergency stop button
can be pressed and the aircraft will descend
FAQ FOR THE DRONE
SITUATION
THE REASON
SOLUTION
1. Receiver LED blinks
continuously for more than 4
seconds once turned on with or
no response to control input .
Unable pair with the
transmitter.
Repeat pairing between
controller and receiver
2. No response after battery is
connected to airaft.
1. Check power supply of
transmitter and receiver.
2. Poor contact on battery
terminals.
3. Check if the power switch
has been turned on.
1. Turn on transmitter and
ensure aircraft battery is
inserted properly.
2. Use fully charged batteries.
3. Re-insert the battery and
ensure secure contact
between battery contacts.
4. Switch to the ON position.
3. Motor does not respond to
throttle stick, receiver LED
fl ashes.
Aircraft battery depleted.
Fully charge the battery or
replace with a fully charged
battery.
4. Main blade spins but unable to
take off.
1. Blade deformation
2. Aircraft battery depleted.
1. Replace main blades.
2. Charge or replace with a
fully charged battery.
5. Strong vibration of aircraft.
Blade deformation.
Replace the blade.
6. Aircraft rotates after trimming
or different speeds between
left /right blades
1. Damaged blades.
2. Damaged motor.
1. Replace blade.
2. Replace motor.
7. Aircraft drifts backward or
forward
Gyroscope not at the
midpoint.
Switch aircraft off and on.
8. Aircraft fails to take off after a
crash or collision.
1. Motor has fallen out.
2. Gears are loose.
1. Install the motor again.
2. Tighten the gears.
8
9
