background image

Page 4

1. Safety Precautions

Serene Wall Hung Split System

 

CAUTION

 

   

Do not

 install the unit in a location that may be exposed to combustible gas leaks. If combustible gas accumulates 

around the unit, it may cause fire.

   

Do not 

install your air conditioner in a wet room such as a bathroom or laundry room. Too much exposure to water 

can cause electrical components to short circuit.

1.  The product must be properly earthed at the time of installation, or electrical shock may occur.
2.  Install drainage piping according to the instructions in this manual. Improper drainage may cause water damage to 

your home and property.

 

SAFETY INSTRUCTIONS

1.  Prevailing WH&S regulations must be observed and will take precedence to the safety instructions contained on 

this manual. Safe work practices and environment must be the paramount importance in the performance of all the 
service procedures.

2.  Ensure that unit installation complies with relevant council regulations and building code standards.
3.  All electrical wiring must be in accordance with current electrical authority regulations and all wiring connections to 

be as per electrical diagram provided.

4.  Always wear appropriate PPE, remove any dangling jewellery and protect long hair by wearing a cap.
5.  Make sure that safety guards and panel covers are always firmly secured and not damaged.
6.  This appliance is not intended for use by young children or infirm persons unless they have been adequately 

supervised by a responsible person to ensure that they can use the appliance safely. Young children should be 
supervised to ensure that they do not play with the appliance.

7.  Installer must incorporate a means of electrical disconnection (isolator) in the sub mains fixed wiring in accordance 

with the Australian wiring rule (AS3000).

8.  Secure the power cords and control cables that goes in/out the unit. Use the cable ties provided in the control box.

 

WARNING

1.  Carefully read all the Safety Precautions before installation.
2.  In certain functional environments, such  as kitchens, server rooms, etc., the use of specially designed                                        

air-conditioning units is highly recommended.

3.  Only qualified HVAC technicians* should install, repair and service this air conditioning unit. Improper service or 

alteration by unqualified technician could result in significant and major damage to the product or property which 
may render your warranty null and void. Such unqualified service could also lead to severe physical injury or death. 
Follow all safety instructions in this literature and all warning labels that are attached to the equipment.

4.  During installation, ensure there are no refrigerant leaks. Refrigerant is toxic and poses a serious health and safety risk.

 * 

Qualifications required will be appropriate Electrical, Refrigeration and Refrigerant 

Handling License & Training, dependent on local State/Territory regulations.

Summary of Contents for Serene WRC-026AS













































Reviews: