background image

9

Care & Maintenance

Display Care

ean  ith a soft, damp c oth.  o not use caustic c eaners or abrasives.  eep 

away from dust, dirt and moisture. Clean ventilation ports regularly with a 

gentle puff of air.

Calibration

The temperature and humidity readings can be calibrated on the display to 

improve accuracy. Calibration can improve accuracy when product placement or 

environmental factors impact your data accuracy.
1. 

o access ca ibration mode, press AN  

 the 

“, “SET”, and “ “   

  buttons simultaneously for at least 5 seconds.
2. To adjust the currently selected item, press and release the “ “ or “ “ 

  buttons to calibrate the data value higher or lower from the actual reading.
3. To save your adjustments, press and release the “SET” button to adjust the 

  next preference. The “ ” icon will remain illuminated next to calibrated values.
After 10 seconds of inactivity, the display will save the adjustments and exit 

calibration mode. 

Note:

 Calibrations will be erased if the display is reset or if the batteries are 

removed.

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:

1- This device may NOT cause harmful interference, and

2- This device must accept any interference received, including interference that may cause undesired operation.

ARN N   hanges or modifications to this unit not e press  approved b  the part  responsib e for comp iance cou d void the 

user s authorit  to operate the equipment.

N

  his equipment has been tested and found to comp   ith the  imits for a  ass   digita  device, pursuant to  art   of the F  

ru es.  hese  imits are designed to provide reasonab e protection against harmfu  interference in a residentia  insta ation.  his equipment 

generates, uses and can radiate radio frequenc  energ  and, if not insta ed and used in accordance  ith the instructions, ma  cause 

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. 

f this equipment does cause harmfu  interference to radio or te evision reception,  hich can be determined b  turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

  ncrease the separation bet een the equipment and the receiver.

  onnect the equipment into an out et on a circuit different from that to  hich the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

N

  he manufacturer is not responsib e for an  radio or   interference caused b  unauthorized modifications to this equipment. 

uch modifications cou d void the user authorit  to operate the equipment.

DISPLAY’S BUILT-IN 
TEMPERATURE SENSOR RANGE

32

º

F to 122

º

F; 0

º

C to 50

º

C

DISPLAY’S BUILT-IN 
HUMIDITY SENSOR RANGE

1% to 99% RH

WIRELESS RANGE

330 ft / 100 m 

depending on home construction materials

OPERATING FREQUENCY

433 MHz

POWER

3 x AA alkaline batteries

Specifications

Summary of Contents for 06043













Reviews: