background image

16 

Adam Equipment 2011 © 

WARRANTY

 

INFORMATION

 

Adam Equipment offers Limited Warranty (Parts and Labour) for the components failed due to 

defects in materials or workmanship.    Warranty starts from the date of delivery. 

During  the  warranty  period,  should  any  repairs  be  necessary,  the  purchaser  must  inform  its 

supplier or Adam Equipment  Company. The company or  its authorised  Technician reserves the 

right to repair or replace the components at any of its workshops depending on the severity of 

the  problems.  However,  any  freight  involved  in  sending  the  faulty  units  or  parts  to  the  service 

centre should be borne by the purchaser. 

The warranty will cease to operate if the equipment is not returned in the original packaging and 

with correct documentation for a claim to be processed. All claims are at the sole discretion of 

Adam Equipment. 

This warranty does not cover equipment where defects or poor performance is due to misuse, 

accidental  damage,  exposure  to  radioactive  or  corrosive  materials,  negligence,  faulty 

installation,  unauthorised  modifications  or  attempted  repair  or  failure  to  observe  the 

requirements  and  recommendations  as  given  in  this  User  Manual.  Additionally  rechargeable 

batteries (where supplied) are not covered under warranty. 

Repairs  carried  out  under  the  warranty  does  not  extend  the  warranty  period.  Components 

removed during the warranty repairs become the company property. 

The statutory right of the purchaser is not affected by this warranty. The terms of this warranty 

is  governed  by  the  UK  law.  For  complete  details  on  Warranty  Information,  see  the  terms  and 

conditions of sale available on our web-site. 

Summary of Contents for PTS 2000





















Reviews: