General Instructions
Installing a Hinged-Pole Kit
96A0345, Rev. H 13 October 2009
2-2
L-807 Wind Cone and ICAO L-807, Installation Manual
2 - Installing a Hinged-
Pole Kit
2.3
General Instructions
Read and understand all instructions before working on the wind cone. De-energize the field circuit connected
to the wind cone before installing the new Center-hinged Pole kit. The assemblies can be powered by either a
series circuit or a voltage power.
2.3.1
Disassemble the old pole
1.
De-energize the Windcone
2.
Lower the Windcone
.
3.
Disconnect the power leads. Loosen the cable clamps and retainers holding the power cable.
4.
Pull the power cable from the Windcone pole. Disconnect the base ground strap.
5.
Remove the (2) 3/8 x 4.25-inch bolts that secures the Cage assembly to the pole.
6.
Remove the Windcone cage assembly carefully. Set aside for the steps to assemble the Windcone cage
assembly to the new hinged-pole.
7.
Unbolt the base. Remove the old pole.
Figure 2.2.
Hinged-pole diagrams 1 of 2
1 = FOR L-807 INT/EXT LIT AND/OR WITH SBOL
2 = FOR L-807 UNLIT AND WITHOUT SBOL
44A6878/ X
.30 - in
DETAIL C
E
E
A
B
3 PLACES
3 PLACES
DETAIL B
SCALE 1 : 4
DETAIL F
SCALE 1:4
TOP TUBE REF
44A6883-1
LED WINDCONE
LWR GND STRAP
60A4062
L-807 WIND CONE HINGED
POLE ADAPTER
65A0015-29
3/8-16 HX NUT
66A0015-29
3/8 FLATWASHER
66A0026-29
3/8 SPLIT LOCKWASHER
BOLT 3/8-16 X 4.25 X 1 HX HD
44A6876-2
TOP TUBE WELD ASSEMBLY
BOLT 1/4-20 X 1.25 HX
HD FULL THREAD
61A0453
1" RUBBER CUSHIONED
SS LOOP STRAP
65A0015/24
1/4-20 HX NUT, SS
66A0026/24
1/4 SPLIT LOCKWASHER
3/4 FLEXIBLE LIQ TIGHT
CONDUIT X 18 IN
77A0208
44A6876-1
BOTTOM TUBE
WELD ASSEMBLY
65A0015/33
1/2-13 HEX NUT
66A0026-33
1/2 SPLIT LOCKWASHER
BOLT 1/2-13 X 2.5 X 1.25 HEX HEAD
5/8 FLATWASHER
61A0451
25-ft WINCH CABLE 7/32" GALV 2500 lb min
42A0601
WINDCONE HINGED POLE
WARNING LABEL
60A4060
L-807 WINDCONE HINGED
POLE WINCH ATTACH BAR
77A0208
3/4 FLEXIBLE LIQ TIGHT
CONDUIT X 18 IN
65A0015/33
1/2-13 HX NUT
66A0015-33
1/2 FLATWASHER
66A0026-33
1/2 SPLIT LOCKWASHER
64A0178-32
1/2-13 X 2 HEX HD
66A0015-33
1/2 FLATWASHER
64A0173-8
1/4-20 X 1/2 HX HD
66A0026/24
1/4 SPLIT LOCKWASHER
65A0015-29
3/8-16 HX NUT
66A0015-29
3/8 FLATWASHER
66A0026-29
3/8 SPLIT LOCKWASHER
64A0176-80
3/8-16 X 5 X 1 HX HD
Summary of Contents for L-807
Page 7: ......
