ADB L-807, Installation Manual

General Instructions

96A0345, Rev. H 13 October 2009
L-807 Wind Cone and ICAO L-807, Installation Manual

2-3

Installing a Hinged-Pole Kit

2 - Installing a Hinged-Pole 

Kit

Figure 2.3.

Hinged-pole diagram 2 of 2

2.3.2

Assemble the Center-hinged Pole

1.

Assemble the upper and lower pole sections using the Hinge Pin and the 316 Stainless Steel Split Ring.

2.

Install the 3/4-inch Flexible Conduit into the hinged opening. See Detail F. 

3.

Pull the Power Cable through the pole.

4.

Attach the Winch Attach Bar. See Detail A. Attach the Winch Cable. See Detail B.

5.

Attach the Winch to the lower pole section. See Section D-D and Detail C. Connect the Winch Cable and 
remove the slack by turing the winch.

6.

Connect the ground strap across the pole hinge. See Detail A.

7.

Connect the pole to the Base and connect the Ground Strap. See Section E-E. 

Do Not Pinch the Cable

. 

8.

Level the pole using the 8-bolts at the base. Using a level, hold in the vertical position and secure the assembly 
to the base with 8 ½ inch hex nuts and flat washers. Torque the hex nuts to 40/42 foot-pounds.

9.

Attach the Windcone Cage Assembly to the Pole. For the LED lighted units: Connect the Ground Strap from 
the top of the pole to the upper Windcone Cage Assembly.

10.

Connect the Power Leads as per the correct wiring diagram. See the L-807 Windcone and ICAO L-807 manual 
96A0345.

3 PLACES

DETAIL A

SCALE 1 : 4

DETAIL C

SCALE 1:4

SEE DETAIL F

D

D

SECTION D-D

SCALE 1 : 4

SECTION E-E

SCALE 1 : 4

Lubricate gears with wear &
weather resistant grease.

Plug fabrication alignment holes with noted hardware.

weld tube assembly.

2 places bottom weld tube assembly and one place top

72A0010

GROUND LUG

64A0173-12

1/4-20 X 3/4 HX HD

66A0026/24

1/4 SPLIT LOCKWASHER

5/8 FLATWASHER

5/8 SPLIT LOCKWASHER

5/8 HEX NUT

60A4060

L-807 WINDCINE HINGED
POLE WINCH ATTACH BAR

66A0015-33

1/2 FLATWASHER

66A0026-33

1/2 SPLIT LOCKWASHER

BOLT 1/2-13 X 5 X 1.25 HX HD

61A0452

316 SS SPLIT

RING 1.34 OD

44A6883-2

LED WC HINGE

GROUND STRAP

64A0173-8

1/4-20 X 1/2 HX HD

66A0038-6

1/4 INT LOCKWASHER

61A0452

316 SS SPLIT RING 1.34 OD

77A0208

3/4 FLEXIBLE LIQ TIGHT CONDUIT X 18 IN

65A0015/33

1/2-13 HX NUT

66A0015-33

1/2 FLATWASHER

64A0178-32
1/2-13 X 2 HEX HD

66A0015-33
1/2 FLATWASHER

60A4063
L-807 WINDCONE HINGE PIN

64A0173-8

1/4-20 X 1/2 HX HD

66A0026/24
1/4 SPLIT LOCKWASHER

61A0450

BRAKE WINCH
DUTTON-LAINSON
DLB1205A

64A0176/16
3/8-16 X 1 HX HD

66A0015-29
3/8 FLATWASHER

66A0026-29
3/8 SPLIT LOCKWASHER

60A4059

WINDCONE HINGED POLE

WINCH MTG BRACKET

Attach after pulling cable