background image

ADCP-80-412 

x

 Issue 1 

x

 April 2000

Page 9

6  CUSTOMER INFORMATION AND ASSISTANCE

For customers wanting information on ADC products or help in using them, ADC offers the
services listed below. To obtain any of these services by telephone, first dial the central ADC
telephone number, then dial the extension provided below.

The central number for calls originating in the U.S.A. or Canada is 

1-800-366-3891

. For calls

originating outside the U.S.A. or Canada, dial country code “1” then dial 

952-946-3000

.

Sales Assistance
Extension 3000

• Quotation Proposals
• Ordering and Delivery
• General Product Information

Systems Integration
Extension 3000

• Complete Solutions (from Concept to Installation)
• Network Design and Integration Testing
• System Turn-Up and Testing
• Network Monitoring (Upstream or Downstream)
• Power Monitoring and Remote Surveillance
• Service/Maintenance Agreements
• Systems Operation

BCG Technical Assistance Center
Extension 3475
E-Mail: technical@adc.com

• Technical Information
• System/Network Configuration
• Product Specification and Application
• Training (Product-Specific)
• Installation and Operation Assistance
• Troubleshooting and Repair

Product Return Department
Extension 3748
E-Mail: repair&return@adc.com

• ADC Return Authorization number and instructions must

be obtained before returning products.

Product information may also be obtained using the ADC web site at 

www.adc.com

 or by

writing ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, MN 55440-1101, U.S.A.

Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. 

In

no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits and ADC further
disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of
liability applies to all products, publications and services during and after the warranty period.

This publication may be verified at any time by contacting ADC’s Technical Assistance Center at 1-800-366-3891, extension
3475 (in U.S.A. or Canada) or 952-946-3000 (outside U.S.A. and Canada), or by writing to ADC Telecommunications, Inc.,
Attn: Technical Assistance Center, Mail Station #71, P.O. Box 1101, Minneapolis, MN 55440-1101, U.S.A.

© 2000, ADC Telecommunications, Inc.

All Rights Reserved

Printed in U.S.A.

Summary of Contents for ADCP-80-412











Reviews: