background image

ADCP-50-404 • Issue 2 • November 1998

2-70000-0344 Page 1

© 1998, ADC Telecommunications, Inc.

DMPS-10CE Power Supply

User Manual

Content Page

Revision History

.......................................................................

1

Admonishments

.......................................................................

1

1. GENERAL

............................................................................

2

2. DETAILED DESCRIPTION

.................................................................

2

2.1 DMPS-10CE Power Supply (Basic)

 ......................................................

2

3. DMPS-10EXP/CE EXPANSION MODULE

........................................................

3

4. SPECIFICATIONS

.......................................................................

4

5. OUTPUT CABLE ASSIGNMENTS

.............................................................

5

6. INSTALLATION

........................................................................

5

6.1 DMPS-10CE Power Supply Installation

....................................................

5

7. DMPS-10EXP/CE EXPANSION MODULE INSTALLATION

.............................................

6

8. POWER-UP OF THE DMPS-10CE POWER SUPPLY

.................................................

7

9. REPLACING THE LINE FUSE

...............................................................

7

10. CUSTOMER INFORMATION AND ASSISTANCE

...................................................

8

Revision History

ISSUE DATE REASON FOR CHANGE

Issue 1 06/96 Original

Issue 2 11/98 Update Customer Information and Assistance section.

Admonishments

Important safety admonishments are used throughout this manual to warn of possible hazards
to persons or equipment. An admonishment identifies a possible hazard and then explains
what may happen if the hazard is not avoided. The admonishments — in the form of Dangers,
Warnings, and Cautions — must be followed at all times. These warnings are flagged by use
of the triangular safety icon (seen below), and are listed in descending order of severity of
injury or damage and likelihood of occurrence.

Danger: Danger is used to indicate the presence of a hazard which will cause severe personal
injury, death, or substantial property damage if the hazard is not avoided.

Warning: Warning is used to indicate the presence of a hazard that can cause severe
personal injury, death, or substantial property damage if the hazard is not avoided.

Caution: Caution is used to indicate the presence of a hazard that will or can cause minor
personal injury or property damage if the hazard is not avoided.

Summary of Contents for DMPS-10CE










Reviews: