background image

ADCP-50-404 • Issue 2 • November 1998

Page 8
© 1998, ADC Telecommunications, Inc.

CAT #
S/N

DATE
CODE

MADE

IN USA

U R

MODEL

VOLTS

HERTZ

DATE CODE

AMPS

OUTPUT
VOLTS

AMPS

PH

CAUTION

ATTENTION

UTION

TENTION

8271-A

CAUTION: DOUBLE POLE

NEUTRAL FUSING

250V  4A T

FUSES

Figure 5. DMPS-10CE Fuse Location

10.  CUSTOMER INFORMATION AND ASSISTANCE

For customers wanting information on ADC products or help in using them, ADC offers the
services listed below. To obtain any of these services by telephone, first dial the central ADC
telephone number, then dial the extension provided below.

The central number for calls originating in the U.S.A. or Canada is 1-800-366-3891. For calls
originating outside the U.S.A. or Canada, dial country code “1” then dial 612-946-3000.

Sales Assistance

• Quotation Proposals

Extension 3000

• Ordering and Delivery

• General Product Information

Systems Integration

• Complete Solutions (from Concept to Installation)

Extension 3000

• Network Design and Integration Testing

• System Turn-Up and Testing

• Network Monitoring (Upstream or Downstream)

• Power Monitoring and Remote Surveillance

• Service/Maintenance Agreements

• Systems Operation

BBG Technical Assistance Center

• Technical Information

Extension 3223

• System/Network Configuration

E-Mail: technical@adc.com

• Product Specification and Application

• Training (Product-Specific)

• Installation and Operation Assistance

• Troubleshooting and Repair/Field Assistance

Product Return Department
Extension 3748
E-Mail: repair&return@adc.com

• ADC Return Authorization number and instructions

must be obtained before returning products.

Product information may also be obtained using the ADC web site at www.adc.com or by
writing ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, MN 55440-1101, U.S.A.

Summary of Contents for DMPS-10CE










Reviews: