Installing Multiplexers
LTPH-SM-1052-04
38
July 14, 2002
HMS-358 List 5 and List 6
HXU-3
5
8
/HXU-3
6
0
Configuring DS1 Services Through the Config Menu
Figure 26.
Setting the T1/E1 Ports through the HXU-358 or HXU-360
Step
Procedure
Installer Check
ü
Use
, ,
,
to navigate through multiplexer menu options and settings.
1
From the Config
menu, select
T1/E1 Ports and then press
.
For more information on navigating through the menu system, refer to the procedures detailed in
“Setting Up Basic System Parameters Through the Config Menu” on page 34
H
2
To configure any of the 28 ports, select the port and change its Srvc Mode to MEM-ADMIN by
pressing the
, and then press
.
H
3
Configure the following options:
•
Type of service T1 or E1 (T1 default)
•
Line code for T1 (Code)
–
AMI
–
B8ZS (default)
•
Line code for E1 (Code)
–
HDB3
•
Line buildout (LBO) options for the channel (133 [default], 266, 399, 533, or 655 feet).
Pertains to T1 only, not applicable for E1.
H
Continued
Main Monitor History
Config
Test Inventory Quit Help
+-------------------+
|
T1/E1 Ports
|
+------------------------------------------------------------------------------+
| Port Srvc Mode LBO Code T1/E1 | Port Srvc Mode LBO Code T1/E1 |
| 1 IN-SRVC 133 B8ZS T1 | 15 OUT-OF-SRVC 133 B8ZS T1 |
| 2 IN-SRVC 133 B8ZS T1 | 16 OUT-OF-SRVC 133 B8ZS T1 |
| 3 IN-SRVC 133 B8ZS T1 | 17 OUT-OF-SRVC 133 B8ZS T1 |
| 4 IN-SRVC 133 B8ZS T1 | 18 OUT-OF-SRVC 133 B8ZS T1 |
| 5 MAINTENANCE 133 B8ZS T1 | 19 OUT-OF-SRVC 133 B8ZS T1 |
| 6 MAINTENANCE 133 B8ZS T1 | 20 OUT-OF-SRVC 133 B8ZS T1 |
| 7 MAINTENANCE 133 B8ZS T1 | 21 OUT-OF-SRVC 133 B8ZS T1 |
| 8 MAINTENANCE 133 B8ZS T1 | 22 OUT-OF-SRVC 133 B8ZS T1 |
| 9 MEM-ADMIN 266 B8ZS T1 | 23 OUT-OF-SRVC 133 B8ZS T1 |
| 10 MEM-ADMIN 399 B8ZS T1 | 24 OUT-OF-SRVC 133 B8ZS T1 |
| 11 MEM-ADMIN 533 B8ZS T1 | 25 OUT-OF-SRVC 133 B8ZS T1 |
| 12 MEM-ADMIN 655 B8ZS T1 | 26 OUT-OF-SRVC 133 B8ZS T1 |
| 13 OUT-OF-SRVC 133 B8ZS T1 | 27 OUT-OF-SRVC 133 B8ZS T1 |
| 14 OUT-OF-SRVC 133 B8ZS T1 | 28 OUT-OF-SRVC 133 B8ZS T1 |
+------------------------------------------------------------------------------+
Use <Spacebar> to cycle through option settings and <Enter> to activate
ID: | Card 'A' 10/01/01 10:42:47 ALARMS: NONE
← ↑ → ↓
ENTER
SPACEBAR
ENTER
