background image

www.addonics.com

Technical Support (M-F 8:30am - 6:00pm PST)   

Phone: 408-453-6212 

Email: www.addonics.com/support/query/

Quick Start

Insert the source and target drives and power up the unit. By default, the 
duplicator will initialize, scan for drives, and offer the copy function. When the 
copy function appears, press ENT to begin copying.

Canceling Functions

When selecting menu options, canceling is done by pressing ESC. When the 
unit is busy performing an operation such as copy, verify, or overwrite, the 
operation can be canceled by holding the ESC button until the unit beeps.

Duplicator Functions

The duplicator has three menu sections: The Main menu, Setup Options, and 
Advanced Setup Options. Setup Options is accessed through the Main 
menu. Advanced Setup Options is accessed by holding the ESC button from 
any other menu until the unit beeps.

1. Copy HDD

Scans the ports, then copies from the source to the target.

2. Compare HDD

Scans the ports, then target will be compared to source.

3. PreScan Source

Reads all blocks on the source drive to confirm no I/O errors are 
encountered.

4. ReScan BUS

Manually scans all ports and reports how many units were found.

5. Source Size

Examines the source drive and reports total space and space used, if 
drive contains compatible partitions. Press up/down to change display, 
ESC to exit.

6. Secure Erase

Scans all ports, then erases all data on all connected drives (including 
Source HDD). NOTE: some drives will remain in a locked state when the 
process is complete. Drives that are locked may not appear to an operating 
system and will cause an I/O error if used as a target in the duplicator. If this 
happens, start secure erase again and hold ESC to cancel the operation a 
few moments after it begins.

7. Overwrite

Overwrite is used to write data onto the entire hard disk, it will destroy all 

data on all HDDs connected to the duplicator (including Source HDD) by 
writing data to all sectors. There are 3 sub-options: One pass , 3 pass and 7 
pass.

8. Setup

Enters the Setup menu. See Setup Options for details.

9. USB Mode

Not supported.

10. Adv Setup

Enters Advanced Setup Options menu. Only available when holding ESC on 
any main menu option. See Advanced Setup Options.

Setup Options:

8-01. Language

Use this option to select the language of the system, currently only English is 
supported.

8-02. Copy Size

Controls how much of the source drive to use for copy operations, in percent-
age. Default setting is ALL (100%).

8-03. Startup Menu

Sets the first menu option to appear after boot. Default setting is Copy HDD.

8-04. Auto Compare

Controls whether or not the target is compared automatically when copy is 
complete. Default setting is OFF.

8-05. Copy with Size

Causes duplicate drive to report to an operating system the exact same total 
size as source when copy is complete. Works only on drives formatted using 
a Master Boot Record. Default setting is OFF.

8-06. Button Sound

Enables audible beep when pressing buttons. Default setting is ON.

8-07. Device Info

Displays information about connected drives. Main display is drive manufac-
turer and size. Press up/down to select drives, ENT to display model number 
and firmware revision of selected drive.

8-08. System Info

Displays firmware version and date.

8-09. Fast Copy

When this setting is ON, the duplicator will attempt to copy the source drive's 
contents instead of the entire disk. Also controls Compare function. Default 
setting is OFF.

NOTE: 

Target drive size is still required to be equal to or greater than source. Only works with 

source drives formatted using Master Boot Record. If the source drive has a boot record other 
than MBR, the entire disk will be copied as if Fast Copy were OFF. If the source drive is 
formatted with a Master Boot Record and contains only FAT32 or NTFS partitions, identical 
partitions will be created on the target(s) and only the files will be copied. If the source drive with 
MBR format includes partitions other than FAT32 or NTFS, all sectors of all partitions (including 
FAT32 and NTFS) will be duplicated.

Enabling Fast Copy may not produce bootable duplicates.

Advanced Setup

10-01. Detect HDD Delay

Sets delay between attempts to detect disk connection or disconnection. 
Default setting is 4 seconds.

10-02. Read Error Skip

Sets whether a sector or block may be skipped if a read error occurs on the 
source drive. Default setting is OFF.

10-03. Update Firmware

Used to apply firmware updates. Connect a drive formatted as FAT contain-
ing one partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a 
drive that is as small as possible is strongly recommended.

10-04. Compare Firmware

Used to confirm correct firmware. Connect a drive formatted as FAT contain-
ing one partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a 
drive that is as small as possible is strongly recommended.

10-05. Quick Erase HDD

Scans the ports, then quickly erases all sectors on all connected drives.

10-06. H/W Diagnostic

Starts comprehensive tests for LCD, SDRAM, HDD ports, and Flash 
memory.

10-07. Load Default

Resets all configuration settings to default.

10-08. Link Option

Enables USB Mode option on the Main Menu. This feature is not supported. 
Default setting is ON.

10-09. USB Auto-Link

Automatically enables USB Mode. This feature is not supported. Default 
setting is ON.

10-10. COPY HPA

Enables copy functions to duplicate the source drive's Host Protected Area. 
Normally this area is defined as not available to a host controller as defined 
by ATA/SATA specifications.

Summary of Contents for HDUSI325-A









Reviews: