Addonics Technologies RR2035ASDML User Manual Download | Manualshive

Page: 6 / 12

background image

Thermal Management Card on the RAID Rack*

Fan1 to Fan8 could be set either “ENABLE” or “DISABLE”. When all the fans are set

on “DISABLE”, the Fan LED will have no light on.

Fan Connectors

Overheat Buzzer

Floppy Power Connector

Ambient Detect Terminal

Temp. Setting

(40°C, 50°C, 60°C)

Fan Detect Selection

Fan, Temperature and Power LED Connectors

www.addonics.com

Technical Support (M-F 8:30am - 6:00pm PST)

Phone: 408-453-6212

Email: www.addonics.com/support/query/

*The Thermal management card in the RR2035ASDES is pre-configured. This diagram is for reference only.

«
...
4
5
6
7
8
...
»

Summary of Contents for RR2035ASDML













Reviews:

No comments

Related manuals for RR2035ASDML

Brand: Bitspower Pages: 4

Brand: CopperOptics Pages: 38

Brand: ZALMAN Pages: 14

Brand: StarTech.com Pages: 2

Brand: D.A.S. Pages: 22

I-CASE SU31-25TY

Brand: Techly Pages: 2

Brand: InWin Pages: 10

Brand: Icy Box Pages: 8

Brand: Icy Box Pages: 12

Brand: Wavetronix Pages: 15

Brand: Icop Pages: 8

Brand: Azio Pages: 34

Brand: Azio Pages: 35

Brand: CHIEF Pages: 8

Brand: GAI-Tronics Pages: 6

AM-ENC Analog Multiplexer Enclosure

Brand: Campbell Pages: 8

Brand: hager Pages: 2

Brand: Panduit Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands