VISTA-50PEN Installation and Setup Guide
22-6
*44
RING DETECTION COUNT
[00]
|
Only applicable if using a 4285/4286 VIP Module and/or if station-initiated downloading
will be used.
Enter 00 to disable ring detection.
Enter 01-14 for ring counts of 1-14.
Enter 15 to select Answering Machine Defeat Mode, which allows the system to receive
calls even when a telephone answering machine is connected to the same phone line. In
the Answering Machine Mode, the caller should let the phone ring once, then hang up,
and call again within 30 seconds. The system, upon hearing one ring followed by
nothing, will not answer the first call, but will ready itself to pick up on the first ring of
the next incoming call that is received within 30 seconds (i.e., the downloader calling
again). Must be 00 for UL commercial burglary installations.
Note: Do not enter 00 if a 4285/4286 is installed.
*45
PRIMARY FORMAT
[1]
This field selects the reporting format for use on the primary telephone number.
Enter the appropriate number for the primary format as follows: 0=Low Speed;
1=Contact ID; 2=ADEMCO High Speed; 3=ADEMCO Express
*46
LOW SPEED FORMAT (PRIMARY)
[0]
Enter the appropriate value: 0=ADEMCO Low Speed; 1=Sescoa/Radionics
*47
SECONDARY FORMAT
[1]
This field selects the reporting format for the secondary telephone number.
Enter the appropriate number for the secondary format as follows: 0=Low Speed;
1=Contact ID; 2=ADEMCO High Speed; 3=ADEMCO Express
*48
LOW SPEED FORMAT (SECONDARY)
[0]
Enter the appropriate value: 0=ADEMCO Low Speed; 1=Sescoa/Radionics
*49
CHECKSUM VERIFICATION
[0,0]
Enter 1 for either or both primary/secondary formats to send a verification digit to
validate the message at the receiver without having to send two message rounds.
Selection is valid for 3+1, 4+1, and 4+2 reports.
Enter 0 if not desired.
*50
SESCOA/RADIONICS SELECT
[0]
Enter 0 if Radionics format is to be used with hexadecimal 0-9, B-F reporting. Enter 1 if
Sescoa format is to be used with only numeric reporting (0-9). Note that selection
applies to both primary and secondary phone numbers.
*51
DUAL REPORTING
[0]
This field allows all reports to be sent to both primary and secondary phone numbers.
Enter 1 if all reports are to be sent to both primary and secondary phone numbers. If
used with Split Reporting option 1 (1*34), Alarms go to both primary and secondary
numbers, while all other reports go to secondary only. If used with Split Reporting
option 2, Alarms go to both lines, Open/Close and Test messages go to secondary only,
while all other reports go to primary.
Summary of Contents for VISTA-50PEN
