ADEMCO VISTA-50PEN Installation And Setup Manual Download

Page: 213 / 214

N.C.

N.O.

2k EOLR

(note 1)

2k EOLR

(note 1)

BELL

SIREN

NO CONNECTION

TRANSFORMER

16.5VAC, 40VA

ADEMCO No.1361

(IN CANADA

USE No. 1361CN)

or 4300 IF

X-10 DEVICES
WILL BE USED

Connect to

24hr. 120VAC,

60 Hz Outlet

Red

Blk

Grn

Yel

REMOTE KEYPAD

Use 4137/6137/6128

5137AD/6139

8112/8122/8132/8142

(Addressable keypads) only

N.C.

2k EOLR

(note 1)

2k EOLR

(note 1)

N.C.

2k EOLR

(note 1,4)

TIP

(BR

)

TIP

)

Handset

Incoming

Phone Line

Telephone connections

using Ademco No. 620

RJ31X direct connect

cord.

EARTH GROUND
Connect to good earth
ground to maintain im-
munity to transients.
See Instructions for
proper grounding.

SMOKE

4190
RPM

4278

PIR

Polling loop rating: 128mA
maximum. See Installa-
tion Instructions for
maximum number of
devices supported and
maximum wire run length.

VISTA-50PEN

SUMMARY OF CONNECTIONS

USE UL LISTED ENERGY CABLE FOR ALL CONNECTIONS

Zone resistance (Excluding EOLR):
ZONE 1,8: 100 OHMS MAXIMUM
ALL OTHER ZONES: 300 OHMS MAXIMUM

ZONE 1

ZONE 2 ZONE 3

ZONE 4 ZONE 5

ZONE 6 ZONE 7

ZONE 8 ZONE 9

2-WIRE SMOKE

DETECT

OR LOOP

(Also suppor

ts NO/NC Burg contacts)

POLLING LOOP

Prog

rammab

le Response

ast/Nor

mal) Loop

TCHING TYPE

GLASS

BREAK DETECT

OR LOOP

Data in

Data out

RED (+)

BLK (-)

Connect to

12VDC, 4AH

or 12VDC, 7AH

GEL CELL

BATTERY

CHARGING

VOLTAGE

13.7VDC

See

Installation

Instructions for

required
capacity

Replace

every

3 years

NOTE:

WHEN POWERING UP

THE PANEL, PLUG THE

TRANSFORMER IN BEFORE

CONNECTING THE BATTERY.

See Installation Instructions

for max # of keypads

and for max wire run length.

ALARM SOUNDER OUTPUT 10VDC - 13.8VDC

AUXILARY POWER OUTPUT
9.6VDC - 13.8VDC,
750mA maximum
Note: Include current drawn
by keypads and polling loop
devices when making
auxiliary power calculations.

NOTES:

1. Zone 1 may be selected for EOLR supervised
or normally closed (no EOLR) operation via
cut jumper. (Cut red jumper for normally closed
operation. Do not cut for Fire Usage). Zones 2-8
may be selected for either operation via program
field *41.

Zone 1 supports 2-wire smoke detectors.
See Installation Instructions for recommended type
and maximum number of detectors supported.
Zone 7 may be used for remote keyswitch arming/disarming.
See Installation Instructions for wiring instructions.
Zone 8 supports 2-wire latching type glass break detectors.
See Installation Instructions for recommended type and
maximum number of detectors supported.

1 2 3 4 5 6 7 8 9

1. Not Used
2. Ground-
3. Out 1 (Ground Start)
4. Ground-
5. Out 2 (fire)
6. Ground-
7. Out 3 (burg/aud. panic)
8. Ground
9. Out 4 (silent panic/
duress)

Optional programming:
Out 1: Open/close or keypad-like sounding
Out 2: Armed LED
Out 4: Ready LED

Ratings for Out 1:
Active: 10VDC-13.8VDC through 4k OHMS
Not Active: 100 OHMS to ground
Ratings for out 2-4:
Active: 10VDC-13.8VDC through 5k OHMS
Not Active: 1k OHMS to ground

N.C.

N.O.

2k EOLR

(note 1,2)

N.O.

N.C.

N.O.

2k EOLR

(note 1)

2k EOLR

(note 1,3)

N.C.

GLASS
BREAK

1 2 3 4 5 6 7 8 9

MAKE CONNECTIONS USING

No. 4142TR CABLE

WARNING: OWNER'S INSTRUCTION NOTICE NOT TO BE REMOVED

Fire

Usage

Burg.

Usage

CONNECTION OF THE FIRE ALARM
SIGNAL TO A FIRE ALARM HEAD-
QUARTERS OR A CENTRAL STATION
SHALL BE PERMITED ONLY WITH
THE APPROVAL OF THE LOCAL
AUTHORITY HAVING JURISDICTION.
THE BURGLAR ALARM SIGNAL SHALL
NOT BE CONNECTED TO A POLICE
EMERGENCY NUMBER.

1. I n 2 (Printer DTR)
2. Ground
3. In 3 (4300 sync)
4. In 4 (4300 sync)
5. Ground
6. Out 5 (4300 data)
7. Out 6 (Printer RXD)
8. Ground
9. Ground

Red Jumper

(note 1)

DOC LOAD NO.: 5

J7 Header J8 Header

BATTERY

TABS

4192SD
SMOKE

WARNING: TO PREVENT

RISK OF ELECTRICAL

SHOCK, DISCONNECT
TELCO JACK BEFORE

SERVICING THIS PANEL.

THIS EQUIPMENT SHOULD BE INSTALLED IN
ACCORDANCE WITH THE NATIONAL FIRE PROTECTION
ASSOCIATION'S STANDARD 72 (NATIONAL FIRE
PROTECTION ASSOC., BATTERYMARCH PARK.
QUINCY, MA. 02269). PRINTED INFORMATION
DESCRIBING PROPER INSTALLATION, OPERATION,
TESTING, MAINTENANCE, EVACUATION PLANNING
AND REPAIR SERVICE IS TO BE PROVIDED WITH
THIS EQUIPMENT.

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM.

Zone response time:
ZONES 1-8: 350mSec-500mSec
ZONE 9: Programmable for

Fast: 10mSec-15mSec
Normal: 350mSec-500mSec

(default response)

COMPLIES WITH FCC RULES, PART 68
FCC REGISTRATION NO. AC398U-68192-AL-E
RINGER EQUIVALENCE: 0.7B

THIS DEVICE COMPLIES WITH PART 15 OF
FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.

(Refer to Installation Instructions for information concerning Direct Wire
Downloading and printer connections using the 4100SM Serial Module.)

ALL CIRCUITS ARE
POWER LIMITED.

Notes For UL Household Fire Installations
1. Use 12VDC, 14AH battery
2. Maximum auxiliary current,
including polling loop 300mA
3. Combined alarm and auxilary power output
and polling loop current must be limited to 750mA
for UL985 Household Fire Installations.

V50PENSOC-001-V0