background image

Battery Indicator Light 

CAUTION: 

The four charging lights may flash in red color 
if the tool is overheated or overloaded. As 
temperature recovers or over-load protection 
is removed, press the switch and the tool can 
be started normally.

 

Current power of the battery will be indicated 
by the battery indicator light when pressing 
the battery button or switching on the tool. 
(Fig. 3) 

Four red LED lights are set to indicate the battery power which can be referred to the following 
table.   

Status of Red LED Lights 

Approx. Battery Power Left 

4 lights lit 

75%

100% 

3 lights lit 

50%

75% 

2 lights lit 

25%

50% 

1 light lit 

10%

25% 

1 light flickered 

Low level 

 

Battery Charging 

1.

 

Battery Charger 

Notice: 

 

The charger applies to charge for specified Li-ion Battery under normal circumstances. 

 

Make sure that the AC voltage of the power source meets the requirement specified on the 
nameplate of the charger. 

 

Due to the continuing program of research and development, the specifications herein are 
subject to change without prior notice. 

2. Charging Operation 

1.

 

Plug the battery charger into the proper AC power source. The charging indicator light will 
flicker in green color and the charger operates in standby mode. 

2.

 

Insert the battery pack fully into the 
battery charger and the charger starts 
charging. 

The battery charger can detect some sort of 
failure caused by the battery and indicates by 
the statuses of the red and green indicator 
lights. 

When a failure occurs, remove the battery 
and then insert it into the charger again. If the failure continues, change with a new battery. If 
the new battery can be charged, then the old battery maybe damaged. If the charging indicator 
lights indicate same failure as before while changing with a new battery, then the charger 
maybe damaged, take the charger to be repaired by qualified serviceman. (Fig. 4) 

The following chart lists the relations between the statuses of charging and charging indicator 
lights. 

Descriptions of 
Charging Status 

Icons 

Icons of Charging 
Indicator Lights 

Descriptions of Charging 
Indicator Lights 

Green 
Light 

Red 
Light 

Plug the charger into 
a proper outlet 

 

 

 

Green light flickers, red light 
extinguished 

During charging 

   

 

Green light extinguished, red 
light keeps

   

flickering 

steadily 

Charge complete 

 

 

 

Green light keeps up   
steadily, red light 
extinguished 

Abnormity occurs on 
the battery 

 

 

 

Green and red light flicker 
alternately 

The temperature of 
the battery is under 
0

 or higher than   

   

 

Green light extinguished, red 
light flickers 

Summary of Contents for MAC AFRIC SDRILC-024












Reviews: