ADENDORFF VLS8TS-1 Instruction Manual Download | Manualshive

Page: 15 / 17

background image

Control lever

1.Rotate the control lever upwards and make it match the hole on the valve seat.
2.Fit the control lever into position using the bolt supplied as shown . The bolt should pass through the hole on
the valve seat .
3.Then tighten the nut.
4.Do the same to the other control lever.

Fix the wood supporting frame into the seat and tighten by screw M10*45.

«
...
13
14
15
16
17
»

Summary of Contents for VLS8TS-1


















Reviews:

No comments

Related manuals for VLS8TS-1

hakki pilke 38 easy TR

Brand: Maaselan Kone Pages: 37

Brand: SpeeCo Pages: 92

Brand: MADER Pages: 72

Brand: Yukon Pages: 20

Brand: Kellfri Pages: 28

Brand: Champion Power Equipment Pages: 32

Brand: King Canada Pages: 10

Brand: Wessex Pages: 8

Brand: Bell Pages: 24

Brand: Bell Pages: 40

Brand: Bell Pages: 48

Brand: Bell Pages: 48

Brand: Bell Pages: 52

Brand: Bell Pages: 60

PICKPINE CELTIS 100 B&S

Brand: Bell Pages: 56

Brand: Bell Pages: 60

Brand: Bell Pages: 92

Brand: BGU Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands