background image

 

 

Important Safeguards and Warnings 

WARNING: Shock and fire hazard

 

If  the  Foil  Heating  Mat  System  is  damaged  or  not  installed  properly,  fire  or  shock  could  occur 

resulting  in  serious  personal  injuries  or  damage  to  property.  You  must  carefully  follow  the 

warnings and instructions contained in this manual. 

· A Thermostat must be used. 

· It is important that this equipment is installed only by qualified electricians who are familiar with 

the proper sizing, installation, construction and operation of floor warming system and the hazards 

involved.  The  installation  must  comply  with  all  national  and  local  electrical  codes.  If  you  are 

unfamiliar with these requirements, contact an electrician. 

· The Foil Heating Mat System is designed for under floor heating purposes only. Be sure that the 

floor  is  not  penetrated  by  nails,  screws,  or  similar  devices  that  can  cause  damage  on  first 

installation or during subsequent floor repairs in the future. 

·  If  the  Foil  Heating  Mat  System  is  damaged,  it  must  be  replaced.  Do  not  attempt  to  splice  or 

repair any part of the system 

 

1 General Information

 

1.1 Use of the Manual 

Installing  Foil  Heating  Mat  is  very  easy  to  do.  Foil  Heating  Mat  Systems  combine  the  highest 

comfort levels with maximum energy efficiency. It’s a proven technology that's safe, reliable and 

energy  efficient.  This  manual  describes  the  Foil  Heating  Mat  floor  heating  system 

  how  to 

design  the  room,  select  the  product,  and  install  the  system.  It  is  important  to  thoroughly  review 

this manual and the following document prior to installation: 

Thermostat Installation and Operation Manual   

For additional information regarding any aspect of the Foil Heating Mat System, contact: 

 

Adept 

Tel: 01394 593110 

mail@adeptfloorheating.co.uk

   

www.adeptfloorheating.co.uk

   

 

1.2 Safety Guidelines 

The safety and reliability of any floor heating system depends on proper design, installation, and 

testing. Incorrect installation or mishandling of the product can cause damage to the heating cable, 

system  components  and  property,  and  can  create  a  risk  of  fire  or  shock.  The  guidelines  and 

instructions contained in this guide are important. Follow them carefully to minimize these risks 

and to ensure that the Foil Heating Mat system performs reliably. 

Pay special attention to the following: 

·

Instructions marked            Important 

·

Safety warnings identified as 

       

WARNING 

 

 

Summary of Contents for HM140/1
















Reviews: