background image

 

 

1.3 Remember to measure resistance 

The  resistance  should  be  measured  between  the  two  conductors,  blue  and  brown.  Compare  this 

resistance reading to the resistance specified in the Product Selection Table. The value should be 

within

 

-5% to +10%. If you get a different reading, contact Adept at 01394 593110. 

Also, measure the resistance between the blue, brown and yellow green ground wire. Both should 

read infinity. If you get a different reading, contact Adept at 01394 593110. 

Please refer to “5 Commissioning” for instructions on how to measure the resistance. 

Important: measure the resistance three times during the installation process 

Remember  to  always  measure,  verify  and  record  the  actual  resistance  throughout  the 

installation process (out of the box, after installation

 

and after installation of wood floor).

 

 

1.4 Lifetime Warranty 

From  the  date  of purchase,  Adept  warrants  that  the  Foil  Heating  Mat  heating  cable  is  free  from 

defects in material, design and workmanship. The extended warranty is only valid if the warranty 

certificate has been properly completed and mailed, and the installation is in accordance with the 

installation instructions. 

 
2 Foil Heating Mat Systems 

2.1 Foil Heating Mat Specifications

 

 

2.2 Foil Heating Mat typical installations and applications 

 

Warning 

Consult the manufacturer for information on special installation requirements for wood, laminate 

and vinyl or linoleum flooring. 

        Important 

· Read the instructions carefully before installing Foil Heating Mat system. 

 

    Cable Construction:

 

Twin conductor

 

    Rated Voltage:

 

230V

 

    Output:

 

140W/m

2

 

 

    Cable spacing:

 

50mm

 

    Cable Diameter:

 

1.0mm

 

    Conductor Insulation:

 

Fluorpolymer

 

    Max. Ambient Temp.:

 

3

0°C(

85

°F)

 

    Min. Installation Temp.:

 

5

°C(

40

°F)

 

    Cold lead 

2-wire plus ground braid; 2.5m length 

Summary of Contents for HM140/1
















Reviews: