GB
GB
5
TECHNICAL DESCRIPTION
U/M
diamond 100s
Cleaning width
mm
1000
Squeegee width
mm
1300
Working capacity, up to
sqm/h
7000
Diameter front cylindrical brush
mm
150
Diameter rear cylindrical brush
mm
280
Diameter side brush
mm
285
Front brush rpm
rpm
933
Rear brush rpm
rpm
500
Side brush rpm
rpm
200
Pressure on the cylindrical brushes
kg
110 max
Pressure on the side brush
kg
35
Brushes motor
W
1800
Motor side brush
W
150
Traction motor
W
1200
Suction motors
W
2x570
Suction vacuum
mbar
190
Type of drive
autom.
Movement speed I-II
km/h
4.5-7,0
Maximum gradient
%
10
Solution tank
l
235
Recovery tank
l
250
Machine length
mm
2025
Machine height (without rollbar)
mm
1330
Machine height (with rollbar and without blinking light)
mm
1795
Machine height (with rollbar and blinking light)
mm
1965
Machine width (without squeegee)
mm
1165
Machine width with side brush in operating position
mm
1250
Weight of the machine (empty and without batteries )
kg
670
Capacity of the batteries
Ah
5
500
Weight of the batteries
kg
600
Compartment of the batteries
mm
655x640x530
Acoustic pressure level (in conformity with EN 60704-1)
dB (A)
---
Class
III
Protection level
IP
X3
Tension
V
36
INTRODUCTORY COMMENT
Thank you for having chosen our machine. This floor
cleaning machine is used for the industrial and civil
cleaning and is able to clean any type of floor. Dur-
ing its advance movement, the combined action of
the brushes and the detergent solution removes the
dirt which is aspirated through the rear suction as-
sembly, giving a perfectly dry surface.
The machine must be used only for such purpose. It
gives the best performance if it is used correctly and
maintained in perfect efficiency. We therefore ask
you to read this instruction booklet carefully when-
ever difficulties arise in the course of the machine’s
use. In case of need, we ask you to contact our ser-
vice department for all advice and servicing as may
prove necessary.
GENERAL RULES OF SECURITY
The rules below have to be followed carefully in or-
der to avoid damages to the operator and to the ma-
chine.
- Read the labels carefully on the machine. Do not
cover them for any reason and replace them imme-
diately if damaged.
- The machine must be used exclusively by author-
ized staff that has been instructed for its use.
- During the working of the machine, pay attention
to other people and especially to the children.
- In case of danger act immediately upon the emer-
gency brake.
- Leaving the machine in parking position, take off
the key and act upon the parking brake.
- Do not mix different detergents, avoiding harmful
odours.
- Storage temperature: between -25°C and +55°C.
- Perfect operating temperature: between 0°C and
40°C.
- The humidity should be between 30 and 95%.
- Do not use the machine in explosive atmosphere.
- Do not use acid solutions which could damage the
machine and/or the persons.
- Do not use the machine on surfaces covered with
inflammable liquids or dusts (for example hydrocar-
bons, ashes or soot).
- In case of fire, use a powder fire-extinguisher.
Do not use water.
- Do not strike shelvings or scaffoldings, where there
is danger of falling objects.
- Adapt the working speed to the adhesion condi-
tions: particularly, slow down before narrow curves
have to be faced.
- Do not use the machine on areas having a higher
gradient than the one stated on the number plate.
- The machine has to carry out simultaneously the
operations of washing and drying. Different opera-
tions must be carried out in restricted areas prohib-
ited to non-authorized personnel. Signal the areas of
moist floors with suitable signs.
- If the machine does not work properly, check by
conducting simple maintenance procedures. Other-
wise, ask for technical advice an authorized assis-
tance centre.
- Where parts are required, ask for ORIGINAL spare
parts to an authorized dealer.
- Use only ORIGINAL brushes indicated in the para-
graph “RECOMMENDED BRUSHES".
- For any cleaning and/or maintenance operation
take off the power supply from the machine.
- Do not take off the protections which require the
use of tools to be removed.
- Do not wash the machine with direct water jets or
with high water pressure nor with corrosive material.
- Every 200 working hours have a machine check
through an authorized service department.
- In order to avoid scales on the solution tank filter,
do not fill the detergent solution many hours before
the machines’ use.
- Before using the machine, check that all panels
and coverings are in their position as indicated in
this use and maintenance catalogue.
- Restore all electrical connections after any mainte-
nance operation.
- Provide for the scrapping of the material of normal
wear following strictly the respective rules.
- When, your machine has to stop activity, provide
for the appropriate waste disposal of its materials,
especially oils, batteries and electronic components,
and considering that the machine itself has, where
possible, been constructed using recyclable materials.
