ADJ ENC176, User Manual

7

S A F E T Y   G U I D E L I N E S

THIS FIXTURE IS COMPOSED OF SOPHISTICATED ELECTRONIC COMPONENTS. TO GUARANTEE 

SMOOTH OPERATION, IT IS IMPORTANT TO FOLLOW ALL INSTRUCTIONS AND GUIDELINES IN 

THIS MANUAL. ADJ PRODUCTS, LLC IS NOT RESPONSIBLE FOR INJURY AND/OR DAMAGES 

RESULTING FROM THE MISUSE OF THIS FIXTURE DUE TO THE DISREGARD OF THE INFORMATION 

PRINTED IN THIS MANUAL. ONLY QUALIFIED AND/OR CERTIFIED PERSONNEL SHOULD PERFORM 

INSTALLATION OF THIS FIXTURE AND ONLY THE ORIGINAL RIGGING PARTS INCLUDED WITH THIS 

FIXTURE SHOULD BE USED FOR INSTALLATION. ANY MODIFICATIONS TO THE FIXTURE AND/OR 

THE INCLUDED MOUNTING HARDWARE WILL VOID THE ORIGINAL MANUFACTURER’S WARRANTY 

AND INCREASE THE RISK OF DAMAGE AND/OR PERSONAL INJURY. ONLY CERTIFIED PERSONNEL 

SHOULD PERFORM INSTALLATION OF THIS FIXTURE.

•  PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

•  THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.

•  DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURER’S 

WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE 

DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE 

MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR 

REPAIRS.

•  DO NOT PLUG FIXTURE INTO A DIMMER PACK!

•  NEVER OPEN THIS FIXTURE WHILE IN USE!

•  UNPLUG POWER BEFORE SERVICING FIXTURE!

•  NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!

•  KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

•  NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

•  RETINA INJURY RISK - MAY INDUCE BLINDNESS!

•  SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

•  MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS)

•  AMBIENT TEMPERATURE RANGE IS 14° F TO 113° F (-10°C TO 45°C). DO NOT OPERATE THE 

DEVICE WHEN AMBIENT TEMPERATURE FALLS OUTSIDE OF THIS RANGE.

•  MINIMUM DISTANCE TO FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET (0.5 METER).

•  DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow approximately 60 

minutes for the fixture to cool down before serving.

•  DO NOT shake fixture, and avoid brute force when installing and/or operating fixture.

•  DO NOT operate fixture if the power cord is frayed, crimped, damaged and/or if any of the power cord con-

nectors are damaged and do not insert into the fixture securely with ease. NEVER force a power cord con-

nector into the fixture. If the power cord or any of its connectors are damaged, replace it immediately with a 

new one of the same power rating.

•  DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. Allow 

approx. 6” (15cm) between fixture and other devices or a wall for proper cooling.

•  When installing fixture in a suspended environment, always use mounting hardware that is no less than 

M10 x 25 mm, and always install fixture with an appropriately rated safety cable.

•  Always disconnect fixture from main power source before performing any type of service and/or cleaning 

procedure. 

•  Only handle the power cord by the plug end. Never pull out the plug by tugging the wire portion of the cord.

•  During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. 

This is a normal process and is caused by excess paint in the interior of the casing burning off from the 

heat associated with the lamp and will decrease gradually over time.

•  Consistent operational breaks will ensure fixture will function properly for many years.

•  ONLY Use original packaging and materials to transport the fixture in for service.