ADJ ENCORE BURST UV IP, User Manual

8

S A F E T Y  G U I D E L I N E S

THIS FIXTURE IS COMPOSED OF SOPHISTICATED ELECTRONIC COMPONENTS. TO 

GUARANTEE SMOOTH OPERATION, IT IS IMPORTANT TO FOLLOW ALL INSTRUCTIONS 

AND GUIDELINES IN THIS MANUAL. ADJ PRODUCTS, LLC IS NOT RESPONSIBLE FOR 

INJURY AND/OR DAMAGES RESULTING FROM THE MISUSE OF THIS FIXTURE DUE TO THE 

DISREGARD OF THE INFORMATION PRINTED IN THIS MANUAL. ONLY QUALIFIED AND/OR 

CERTIFIED PERSONNEL SHOULD PERFORM INSTALLATION OF THIS FIXTURE AND ONLY 

THE ORIGINAL RIGGING PARTS INCLUDED WITH THIS FIXTURE SHOULD BE USED FOR 

INSTALLATION. ANY MODIFICATIONS TO THE FIXTURE AND/OR THE INCLUDED MOUNTING 

HARDWARE WILL VOID THE ORIGINAL MANUFACTURER’S WARRANTY AND INCREASE THE 

RISK OF DAMAGE AND/OR PERSONAL INJURY. ONLY CERTIFIED PERSONNEL SHOULD 

PERFORM INSTALLATION OF THIS FIXTURE.
•  PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

•  THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.

•  DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR 

MANUFACTURER’S  WARRANTY.  DAMAGES  RESULTING  FROM  MODIFICATIONS TO THIS 

FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN 

THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY 

WARRANTY CLAIMS AND/OR REPAIRS.

•  DO NOT PLUG FIXTURE INTO A DIMMER PACK!

•  NEVER OPEN THIS FIXTURE WHILE IN USE!

•  UNPLUG POWER BEFORE SERVICING FIXTURE!

•  NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!

•  KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

•  NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

•  RETINA INJURY RISK - MAY INDUCE BLINDNESS!

•  SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

•  MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS)

•  AMBIENT OPERATING TEMPERATURE RANGES FROM -4°F to 113°F (-20°C TO 45°C). DO 

NOT OPERATE THE DEVICE WHEN AMBIENT TEMPERATURE FALLS OUTSIDE OF THIS 

RANGE.

•  MINIMUM DISTANCE TO FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET (0.5 

METER).

•  DO  NOT  TOUCH  the  fixture  housing  during  operation.  Turn  OFF  the  power  and  allow 

approximately 60 minutes for the fixture to cool down before servicing.

•  DO NOT shake fixture, and avoid brute force when installing and/or operating fixture.

•  DO NOT operate fixture if the power cord is frayed, crimped, damaged and/or if any of the power 

cord connectors are damaged and do not insert into the fixture securely with ease. NEVER force 

a power cord connector into the fixture. If the power cord or any of its connectors are damaged, 

replace it immediately with a new one of the same power rating.

•  DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. 

Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling.

•  When installing fixture in a suspended environment, always use mounting hardware that is no less 

than M10 x 25 mm, and always install fixture with an appropriately rated safety cable.

•  Always disconnect fixture from main power source before performing any type of service and/or 

cleaning procedure. 

•  Only handle the power cord by the plug end. Never pull out the plug by tugging the wire portion of 

the cord.

•  During the initial operation of this fixture, a light smoke or smell may emit from the interior of the 

fixture. This is a normal process and is caused by excess paint in the interior of the casing burning 

off from the heat associated with the lamp and will decrease gradually over time.

•  Consistent operational breaks will ensure fixture will function properly for many years.

•  ONLY use original packaging and materials to transport the fixture for service.