ADJ Products, LLC - www.adj.com - VBar Pak User Manual Page 12
ADJ Products, LLC - www.adj.com - VBar Pak User Manual Page 13
VBar Pak ADJ LED RC2
VBar Pak ADJ LED RC2
The
ADJ LED RC 2
infrared remote has many differnet functions and
gives you complete control of your VBar. To control the your desired
fixture you must aim the controller at the front of the fixture and be no
more the 30 feet away. To use the ADJ LED RC 2 you must first acti-
vate the fixtures infrared receiver, to activate the receiver please see
the instructions on page 10.
BLACKOUT
-
Pressing this button will blackout the fixture.
SELECT PROG
-
This button will let you access the 4 built-in running
modes; static color mode, color fade mode, color change mode, and
both color fade & color change modes. Each press of the button will
switch to the next running mode.
• When the Red LEDs flash 2 times, this indicates that you are in
Static Color mode. Use the “+” & “-” buttons to scroll through the
static colors, or press two numbers to choose 1 of the 15 static col-
ors. Press FLASH button to activate strobing and use the “+” & “-”
buttons to adjust the flash rate.
Example: Press “0-3” to select static color 3 or press “1-2” to select
static color 12.
• When the Green LEDs flash 2 times, this indicates that you are in
Color Fade & Color Change mode. Press SPEED button and use the
“+” & “-” buttons to adjust the fade/change speed.
• When the Blue LEDs flash 2 times, this indicates that you are in
Color Fade mode. Press SPEED button and use the “+” & “-” buttons
to adjust the color fade speed.
• When the Amber LEDs flash 2 times, this indicates that you are in
Color Change mode. Press SPEED button and use the “+” & “-” but-
tons to adjust the color change speed.
FLASH
-
This button will activate the strobe effect. You can control
the flash rate by pressing the “+” and “-” buttons. Press this button
again to exit strobe mode.
SPEED
-
Press this button to activate and use the “+” & “-” buttons
to adjust the speed of color fade and color change mode, color fade
mode, color change mode, and the sound sensitivity level.
DMX MODE -
This button will let you select which DMX mode you
want to use. Some fixtures will come with different DMX channel
modes. Press the “+” & “-” buttons to switch DMX channel modes
Please see pages 15-20 for DMX modes, values, and traits.
• If the Red LED’s glow you are in DMX Mode 1: 1 Channel Mode.
• If the Green LED’s glow you are in DMX Mode 2: 2 Channel
Mode.
• If the Blue LED’s glow you are in DMX Mode 3: 3 Channel Mode.
• If the Amber LED’s glow you are in DMX Mode 4: 4 Channel
Mode.
• If the Red & Green LED’s glow you are in DMX Mode 5: 5
Channel Mode.
• If the Red & Blue LED’s glow you are in DMX Mode 6: 6 Channel
Mode.
• If the Red & Amber LED’s glow you are in DMX Mode 7: 7
Channel Mode.
• If the Green & Blue LED’s glow you are in DMX Mode 8: 8
Channel Mode.
SL/SA (Slave/Sound Active) -
This button lets you switch between
Slave mode in a Master-Slave configuration and Sound Active mode.
When the fixture is in Sound Active mode, use the “+” & “-” buttons to
scroll through the 16 sound active modes. To adjust the sound sensi-
tivity, press the SPEED button and use the “+” & “-” buttons to adjust
the senstivity.
SET ADDRESS -
Press this button to set the DMX address. Press
this button first, then press the numbers to set the address.
Example: Set DMX Address 1 Press “S-0-0-1”
Set DMX Address 245 Press “S-2-4-5”
R G B A -
Press either one of these buttons and the press the “+” or
“-” to adjust the brightness.
“+” and “-” -
Use these buttons to adjust the flash rate speed, pro-
gram speed, sound sensitivity, DMX channel modes, and program
selection.
DMX Control:
Operating through an DMX controller gives the user the freedom to
