background image

 

 

Page 8

 

cExpress-HL

 

2.4

 

Audio 

¾

 

Integrated

: Intel® HD Audio integrated in PCH QM87 

¾

 

Codec

: Realtek ALC886 on Express-BASE6 

2.5

 

LAN 

¾

 

Integrated

: MAC integrated in SOC 

¾

 

Intel PHY

: Intel® Ethernet Controller i218LM 

¾

 

Interface

: 10/100/1000 GbE connection 

2.6

 

Multi I/O and Storage 

¾

 

Integrated

: in SOC 

¾

 

USB ports

: 2 ports USB 3.0 (USB0,1) and 6 ports USB 2.0 (USB2,3,4,5,6,7) 

¾

 

SATA ports

: four ports SATA 6Gb/s  

¾

 

GPIO

: 4 GPO and 4 GPI with interrupt 

2.7

 

Serial I/O on Module  

¾

 

Chipset

: Nuvoton NCT5104D  

¾

 

Ports

: two UARTs RX/TX only 

¾

 

Console Redirection

: selectable in BIOS over UART0 or UART1 

2.8

 

TPM (Trusted Platform Module) 

¾

 

Chipset

: ATMEL

AT97SC3204 

¾

 

Type

: TPM 1.2 

2.9

 

SEMA Board Controller 

¾

 

Type

: ADLINK Smart Embedded Management Agent (SEMA) 

¾

 

Supports

 

Voltage/Current monitoring 

 

Power sequence debug support 

 

AT/ATX mode control 

 

Logistics and Forensic information 

 

Flat Panel Control 

 

General Purpose I2C 

 

Failsafe BIOS (dual BIOS ) 

 

Watchdog Timer and Fan Control 

2.10

 

Debug 

¾

 

40-pin flat cable connector to be used with DB-40 debug module 

Supports: BIOS POST code LED, BMC access, SPI BIOS flashing, power testpoints, debug LEDs 

¾

 

60-pin XDP header for ICE debug of CPU/chipset 

Summary of Contents for cExpress-HL




















































































Reviews: