background image

CHIMNEY INSTALLATION 

(CONTINUED)

15)  STRAIGHT  CHIMNEY  SECTIONS 

–  Before  running 

the  straight  chimney  through  the  roof,  slide  the 
Firestop  Spacer  (shown  in  FIG.  16)  over  the  Return 
Elbow.  Now,  snap  the  remaining  Straight  Chimney 
sections into place.  

  If the chimney is 30’ or higher, a support section (a 

4‐strap  x  12”  length  of  pipe)  is  required  after  a 
straight chimney section above the fireplace run, or 
above a Return Elbow. The support section will sup‐
port the increased weight of the chimney. 

FIG. 15 ‐ 

STRAIGHT CHIMNEY 

15 

MODEL 

A  

KIVA18 & KIVA 24 

KIVA30  

GAS ONLY 

17 

1

/

2

” 

WOOD OR GAS 

20 

1

/

2

” 

17 

1

/

2

” 

2” MIN. AIR 

SPACE TO 

COMBUSTIBLES! 

 

FIG. 15.1 ‐ 

10’ RULE 

10‐FOOT RULE 

All  chimney  terminations  must  extend  at  least  3’ 

above the highest point where it passes through the 
roof  and  must  be  2’  above  the  peak  of  the  roof  or 
any other building structure within a horizontal dis‐
tance of 10’.  

 

16 

FIG. 16 ‐ 

FIRESTOP SPACERS 

 

16)  FIRESTOP  SPACERS 

–  Firestop  Spacers  are  required  at 

each point where the chimney penetrates a floor or ceil‐
ing joist space. Attach Firestop Spacer to joist using wood 
screws.  

  If the chimney pipe passes through a framed opening into 

an  attic  space,  the  Firestop  must  be  placed  in  the  attic 
floor.  When  the  pipe  passes  through  a  framed  opening 
into living space above, the Firestop must be placed onto 
the ceiling from below. 

  Refer  to  local  building  codes  and  restrictions  for  varia‐

tions in Firestop spacer requirements. 

17) CHIMNEY ROOF FLASHING 

– A flat Chimney Roof Flash‐

ing is used for flat roofs and chimney chases. For pitched 
roofs  a  pitched  flashing  is  used.  Slide  the  Chimney  Roof 
Flashing  down  over  the  last  section  of  straight  chimney 
penetrating the roof or chase and attach to roof. 

  

17 

FIG. 17 ‐ 

CHIMNEY ROOF FLASHING 

 

IMPORTANT: 

If an exposed portion of chimney is greater than 5’ 

above the roof line, use support wires to keep chimney secure. 
The  support  wires  may  be  attached  to  the  outer  pipe  of  the 
chimney with screws but must not penetrate the inner flue pipe.

WARNING: 

DO NOT SEAL VENTILATION OPENINGS ON THE ROOF 

FLASHING!

 

16 

Summary of Contents for KIVA 18 Ornito
























Reviews: