35
34
Method of Usage
Method of Usage
1.Enter the smart device main menu. Open "Settings" and select the "Bluetooth"
option. Open "Bluetooth", and Bluetooth will automatically "Search for a New
Bluetooth Device".
2.The smart device will search for the corresponding Bluetooth model (e.g. IMCM-
XXXX). Click the "Match" button. If you are asked whether to match with the
device, you just select "Match" to complete matching.
3.Turn on "Music Player" in the smart device and select the song to play.
V. Operation Instructions for Bluetooth Speaker Play
VI. Turn off the power and stop massage
·
If the power button is pressed during massage, it will stop all the massage
functions immediately, and the backrest, the legrest and massage chair
manipulators will go back to the default positions. When the preset massage time
is up, all the massage functions will be OFF. The backrest and the legrest will not
go back to the default positions.
·
Shut off the power supply of this product, as shown in the attached figure (Power
Shut-off Diagram of the Product).
VII. Installation Instructions for Armrests
1.Unpack the two packages. Lift out the massage chair and armrest components.
Carefully check the accessories and appearance for any damage. Then assemble
them with a Phillips screwdriver. Then find the supplied power cord and remote
controller from the package. Firstly, insert the remote controller into the front
socket on the right side of the massage chair and tighten it (Figure 1); then plug in
the power cord, and turn on the switch to power on. At this moment, the massage
chair will start the automatic recovery action. After it is changed from the lying and
packing state to the standing standby state, unplug its PUS for assembly
.
2.Raise the rear end of the armrest,respectively insert the plug and trachea
corresponding with the same mark on the rear end of the armrest with the
connecting plug and trachea at the back of the backrest,and the match should be
in place and firm(Figure 2).
Power Shut-off Diagram of the Product
Disconnection Diagram
Unplugging Diagram
POWER INPUT
POWER INPUT
ON/O
FF
ON/O
FF
IV Voice Control Mode
.
·
When the massage chair is turned on or in standby mode, the sound “Hi Alice” or
“Hey Alice” will be produced to enable the voice control function.
·
Long press 3 seconds to turn on or off the voice control function.
·
After such function is enabled successfully, the massage chair will reply “I am here”
At this moment, once a corresponding voice control entry to be implemented is
given within six seconds, the corresponding voice control function can be performed
after a reply is received from the massage chair; if no correct voice control entry is
given within six seconds, the voice control function automatically will be off
automatically and needs to be enabled again.
·
Note: When waking up the voice control function, please use English, the speech
rate is moderate, Voice commands should be follow up the Voice entry.
VOICE CONTROL ENTER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
No.
Voice control entry
Massage on
Massage close
Comfort Massage
Relax massage
Full body massage
Neck massage
Back and waist massage
Stretch massage
Open the air pressure
Close the air pressure
Up the seat position
Down the seat position
Change the other mode
Go little down
Go little up
Answer entry
Answer: Ok, massage on
Answer: Ok, massage close
Answer: Ok, comfort massage
Answer: Ok, relax massage
Answer: Ok, full body massage
Answer: Ok, neck and shoulder massage
Answer: Ok, back and waist massage
Answer: Ok, stretch massage
Answer: Ok, open the air pressure
Answer: Ok, close the air pressure
Answer: Ok, up the seat position
Answer: OK, down the seat position
Answer: OK, change the other mode
Answer: Ok, go little down
Answer: Ok, go little up
Press at least 3 second “ ” button on the armrest (on/off Voice Control mode) .
Make sure the device is on Voice Control mode. Call “Hi Alice” or “Hey Alice”
before the following Commands:
Note: commands 14 and 15 can only be used after command 13.
