background image

Air Handler Limited Warranty – Standard 5 Year 

(Applies only to product installed within the United States or Canada) 

 

Term of Standard Warranty

:  Advanced Distributor Products (ADP) warrants that products sold shall be of 

merchantable quality, free of defects in material and workmanship, under normal use and service, for a period of 
five (5) years from the date of installation, 

not 

to exceed six (6) years from the date of manufacture.  Use of this 

product other than in a residential application will limit the warranted term to a period of (1) year from the date of 
installation, not to exceed two (2) years from the date of manufacture. 
  

Warranty Procedure:

  Warranty parts should be replaced by a qualified local contractor or dealer and will 

require the following information:  model number, serial number, date of installation and an accurate description 
of the problem.  Contractor or dealer will contact a local ADP distributor for replacement parts. 
 

Replacement Parts:

  If, during the term of this warranty, a warranted part fails, ADP will either provide a 

replacement part free of charge, or may at its option, grant a credit for the original purchase  price of the 
defective article to a distributor of ADP products.  ADP may require the return of a defective article for factory 
inspection to verify and/or determine the root cause of the failure.  Covered components include all parts of this 
unit except for the following 

excluded components

, which are not covered by this warranty: cabinet, cabinet 

pieces, wiring and wiring harnesses. 
 

Care of Equipment:  

For this warranty to apply, ADP product must be properly installed, operated, and 

maintained in accordance with the installation, operation and maintenance instructions provided with each unit.  
Unauthorized alteration of ADP product may void this warranty. 

 
Conditions of Warranty:

   Replacement parts furnished under this warranty will be warranted for the balance of 

the original warranty term of the unit and will not serve to extend the original term.  This warranty is void if the 
ADP product is removed from the original installation site.  This warranty does not apply to damage caused by 
shipping, misuse,  mishandling or damage caused by floods, winds, fires, lightning, or exposure to corrosive 
elements/environments (such as salt, chlorine, fluorine or other damaging chemicals). 

 
Limitations of Warranty:

  The costs of refrigerant, refrigerant reclamation, miscellaneous material and labor 

charges for diagnostics, servicing or replacing parts are not covered.  ADP shall have no liability for expenses 
incurred for repairs without prior, written authorization from ADP.  No purchaser, distributor, dealer, 
representative, agent, person, firm or corporation has authority to alter, add to or modify this warranty, either 
orally or in writing.   

 
No Other Warranties:
  

ADP makes no warranty, express or implied, of fitness for any particular purpose, or of 

any other nature whatsoever, with respect to products manufactured or sold by ADP hereunder, except as 
specifically set forth above and on the face hereof.  Any implied warranty of merchantability or fitness for a 
particular purpose on this product is limited in duration to the duration of this warranty.  Some states and 
provinces do not allow limitations on how an implied warranty lasts, so the above limitation may not apply to 
you.  It is expressly understood and agreed that ADP shall not be liable to buyer, or any customer of buyer, for 
direct or indirect, special, incidental, consequential or penal damages, or for any expenses incurred by reason of 
the use or misuse by buyer or third parties of said products.  To the extent said products may be considered 
“consumer products”, as defined in Sec. 101 of the Magnuson-Moss Warranty-Federal Trade Commission 
Improvement Act, ADP makes no warranty of any kind, express or implied, to “consumers,” except as 
specifically set forth above on the face hereof.  The foregoing is in lieu of all other warranties, express or 
implied, not withstanding the provisions of the Uniform Commercial Code, the Magnuson-Moss Warranty-
Federal Trade Commission Improvement Act, or any other statutory or common law, federal or state. 
 

 
 

2175 West Park Place Boulevard 

Stone Mountain, Georgia  30087 

www.adpnow.com 

 

19

Summary of Contents for MX Series





















Reviews: