Adrian Olson ODOM Assembly Manual Download | Manualshive

Page: 22 / 23

background image

Put your

O

D

Logo on the port side of the Main Sail 1" from the front edge and 9" down from the top.

Tie one end of a length of Small String to the top of the Main Sail. Tie the other end to the lower hole in the Masthead
Crane so the top of the Main Sail is approx. 1" below the Masthead Crane.

Install the Keel using (2) Nylock Nuts and (2) Washers with rubber seals,
rubber side down toward the Keelson Block. Place your ODOM in the
boat stand.

Insert the wire end of the Pushrod into the outer hole in the Steering
Control Horn. Install the Rudder into the Rudder Tube. Slide the Steering
Control Horn onto the Rudder Shaft and secure by tightening the set
screw with a 3/32" allen wrench (use the Drain Plug hole for easy access).
Attach the Clevis on the forward end of the Pushrod to the steering Servo.

The Main and Jib Sheets are made from Small String and are used to control to movement of the Main and Jib Sails.
Tie a Sheet Connector to one end of each Sheet and rout the Sheets as shown.

Feed the Downhaul line through the Boom Tang, up through the grommet in the lower front corner of the Main Sail,
back down through the Tang and through the last hole in the Large Plastic Bowsie (then tie a knot).

Attach the Outhaul in the same manner as you did on the Jib Sail. Also add a loop of Small String through the same
grommet as the Outhaul and around the Boom.

Tape an 1/8" diameter drill bit or dowel (as a spacer) to the front of the Mast where one of the small grommets is located.
Securely tie a length of Small String through the grommet and around the Mast and spacer. Remove the spacer and
repeat for all 8 grommets in front edge of the Main Sail.

STEP 3

Installing the Main Sail

SECTION H

STEP 1

Final Assembly

Install the Keel and Rudder

STEP 2

Main Sheet and Jib Sheet

© 2010 by Adrian Olson. All rights reserved.

Page 22

Small Metal Bowsie

Jib Sheet through Chainplate

1/16" hole

Jib Sheet Exit Guide

Jib Sheet Connector

Short end of

Sail Control Arm

Long end of

Sail Control Arm

Main Sheet Exit Guide

Main Sheet Connector

1/16" hole

Small Metal Bowsie

«
...
20
21
22
23
»

Summary of Contents for ODOM
























Reviews:

No comments

Related manuals for ODOM

Strike Eagle G1670B Cargo Plane

Brand: Laser Pegs Pages: 8

Brand: Laser Pegs Pages: 2

Mickey Mouse Cafe

Brand: VTech Pages: 20

Learn & Groove Shakin Colors Maracas

Brand: LeapFrog Pages: 12

Brand: Kyosho Pages: 15

Mighty Mini P-51B

Brand: MiniacRC Pages: 51

Brand: Stevens AeroModel Pages: 29

Brand: Beyblade Pages: 2

Clipped Wing Cub 250

Brand: E-FLITE Pages: 40

Onaga Rocket Kohaya

Brand: BLOTZ Pages: 6

Brand: POLA G Pages: 4

Brand: E-FLITE Pages: 20

Row Your Boat Set BD37315Z

Brand: Our Generation Pages: 2

Origami 3D Fox 2575

Brand: Alexander Pages: 68

AERO SUBARU 30EP

Brand: KK Hobby Pages: 4

Brand: GRAUPNER Pages: 25

Claw Slash Ramjet 83757

Brand: Hasbro Pages: 2

Brand: MINICRAFT Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands