background image

–  15  – 

 

GSMVLP-ADT Status Displays 

[E] 

 

PriRSSI GPRS REG 
-xxxdbm     x        x

 

GSMVLP-ADT Status Display Screen 1 

PriRSSI – Primary Site RSSI level in dbm 
GPRS    – GPRS Service availability where “x” can be: 
                 “Y” if GPRS is available 
                 “N” if GPRS is Not available 
REG      – Registration status from radio module where  
                 “x” can be: 
                  N – Not Registered 
                  H – Registered Home 
                  S – Searching 
                  D – Registration Denied 
                  R – Registered Roaming 
                  ? – Unknown Registration State 
Press the [space] key to go to the next screen. 
Press the [backspace] key to go to the last screen. 

 

 

Cntry Netw LAC 
xxx   xxx   xxxxx

 

GSMVLP-ADT Status Display Screen 2

 

Cntry – Country Code 
Netw – Network Code 
LAC – Local area code 
Press the [space] key to get to the next screen. 
Press the [backspace] key to go to the previous field. 

 

 

Cell BaseSt Chan 
xxxxx       x     xxx

 

GSMVLP-ADT Status Display Screen 3

 

Cell – Base Station ID 
BaseSt – Base Station Antenna Sector 
Chan – Control Channel in use 
Press the [space] key to go to the next screen. 
Press the [backspace] key to go to the previous field. 

 

 

Second Site RSSI 
-xxxdbm

 

GSMVLP-ADT Status Display Screen 4

 

Secondary GSMVLP-ADT Site RSSI level in dbm. 
Press the [space] key to go to the GSMVLP-ADT Status Display 
Screen 1. 
Press the [backspace] key to go to the previous field. 

[S] 

 

ECP                        Flt 
                               OK

 

ECP Mode 

Displays the mode of operation and system fault status. 

[T] 

 

Test Msg Sent 

 

Test Alarm 

Sends a Test alarm to AlarmNet. Functional for a 

registered

 

GSMVLP-ADT only. If the device is not registered, a message is 
displayed indicating that the command cannot be executed. 

[X] 

 

Reset CPU Y/N   

 

Reset the GSMVLP-ADT. 

Pressing [N] returns to normal mode.   
Pressing [Y] resets the device.  
 

 

 

Summary of Contents for GSMVLP-ADT

























Reviews: