background image

–  18  – 

 

FAULT, RED

MESSAGE, YELLOW

STATUS, GREEN

GSMVL-003-V0

A

FAULT, RED

MESSAGE, YELLOW

STATUS, GREEN

B

 

Figure  8 

 A Configured GSMVLP-ADT Status Display (A) and  

an Unconfigured GSMVLP-ADT Status Display in Normal Operating State (B) 

 

FAULT, RED

MESSAGE, YELLOW

STATUS, GREEN

GSMVL-004-V0

4

3

2

1

MAXIMUM SIGNAL

STRENGTH, GREEN

 

Figure 9 

 LED Sequence for a Configured GSMVLP-ADT Message Transmission 

 
CENTRAL STATION MESSAGES 

The following messages are sent to the Central Station by the GSMVLP-ADT module for the conditions 
listed below. 

Table 4 

 GSMVLP-ADT Central Station Messages 

Alarm Condition 

ECP Mode 

Alarm Code 

 

ECP Mode 

Restore Code 

 

Power On Reset 

E339 C0803  

 

ECP Supervision 

E355 C0000  

R355 C0000  

Communication Path Restore 

 

R350 C0951 

Test 

5555 5555 9 

 

Note:

 The control panel sends its own general code (E353) for a trouble condition.  

 

GSMVLP-ADT DOWNLOADING 

General Information 

The GSMVLP-ADT can be used to provide high-speed up/downloading to QuickConnect 3000 control 
panels over the GPRS network via ECP

 communication. This allows site maintenance 

independent of central station monitoring, and modification to sites globally.   

U

U

U

UL

L

L

L

 

Downloading may only be performed if a technician is at the site. 

Summary of Contents for GSMVLP-ADT

























Reviews: