background image

64179008APL1-5A

1

Total Access 1000 Data Access Terminal

Installation and Maintenance

Section 64179008APL1-5A

Issue 1, April 2003

CLEI Code: VAM2KLOF_ _

CONTENTS

1.

GENERAL ........................................................................... 1

2.

INSTALLATION/OPERATION ........................................ 7

3.

PROVISIONING ............................................................... 10

4.

TESTING ........................................................................... 23

5.

HDSL2 DEPLOYMENT GUIDELINES ......................... 23

6.

SPECIFICATIONS ........................................................... 24

7.

MAINTENANCE .............................................................. 24

8.

WARRANTY AND CUSTOMER SERVICE ................. 25

Appendix A. Quick Start Guide – ADSL plus POTS .............. A-1

FIGURES

Figure 1.

Total Access 1000 DAT ......................................... 1

Figure 2.

Total Access 1000 DAT Inside Layout ................. 2

Figure 3.

Total Access 1000 DAT Typical Application ....... 3

Figure 4.

Total Access 1000 DAT HDSL2 Connections ...... 4

Figure 5.

Total Access 1000 DAT Quad ADSL plus
POTS Access Module ............................................. 5

Figure 6.

Total Access 1000 DAT PSU ................................. 5

Figure 7.

Total Access 1000 DAT Quad H2LIU .................. 6

Figure 8.

Total Access 1000 DAT ATM BCU ...................... 6

Figure 9.

Total Access 1000 DAT Menu Tree .................... 12

Figure 10.

ATM Port Provisioning Menu .............................. 13

Figure 11.

ATM PVC/PVP Management Menu ................... 14

Figure 12.

ATM Traffic Parameter Defaults Menu .............. 14

Figure 13.

IMA Facilities Provisioning Menu ...................... 15

Figure 14.

IMA Group Provisioning Menu ........................... 16

Figure 15.

Group Failure Monitoring Status Screen ............. 17

Figure 16.

All Links Failure Monitoring Status Screen ........ 17

Figure 17.

Present Performance Monitoring Statistics
Screen for All IMA Links .................................... 18

Figure 18.

LIU Span Status Screen ........................................ 19

Figure 19.

LIU Performance Monitoring Statistics ............... 20

Figure 20.

Quad ADSL Status Screen ................................... 21

Figure 21.

Quad ADSL Circuit Overview Screen ................. 22

Figure 22.

H2LIU Network Loopback .................................. 23

Figure 23.

HDSL2 Deployment Guidelines .......................... 23

Trademarks: Any brand names and product names included in this document are

trademarks, registered trademarks, or trade names of their respective holders.

TABLES

Table 1.

Total Access 1000 DAT Compliance Codes ......... 7

Table 2.

Termination Block Pin Assignments ..................... 8

Table 3.

Front Panel LEDs ................................................... 9

Table 4.

ATM BCU Front Panel LEDs .............................. 10

Table 5.

Quad ADSL plus POTS Access Module
Front Panel LEDs ................................................. 10

Table 6.

HDSL2 Loss Value ............................................... 24

Table 7.

Loop Insertion Loss Data ..................................... 24

Table 8.

Total Access 1000 DAT Specifications ............... 24

1. GENERAL

This practice provides installation and maintenance
procedures for the ADTRAN Total Access 1000 Data
Access Terminal (DAT).  

Figure 1

 is an illustration of

the Total Access 1000 DAT enclosure.  Refer to

Appendix A

 for the quick start guide for ADSL plus

POTS.

Revision History

This is the initial release of this document. Changes in
future revisions will be noted in this subsection.

Description

The Total Access 1000 DAT is a high performance
remote DSLAM system for deploying DSL and voice
services.  A small and versatile platform, the Total
Access 1000 DAT uses span powering along with
IMA signaling to deliver 12 ADSL plus POTS loops
from two, three, or four HDSL2 spans.  This design
provides carriers the flexibility needed to meet
customer service commitments.

Figure 1.  Total Access 1000 DAT

Summary of Contents for Total Access 1000































Reviews: