background image

26

4. 

Proper storage temperature. 

Ensure storage is within the temperatures specified 

below.

•  -20°C to 45°C (-4°F to 113°F)

NOTICE

•  Leaving the battery connected to a load or power electronics during storage may 

subject the battery to discharge, resulting in irreversible damage and voiding the 
warranty.

NOTICE

•  Storing the battery outside specified temperatures will result in irreversible damage 

and void the warranty.

•  Storing or leaving the battery at 0% SOC will result in irreversible damage and void 

the warranty.

•  Allowing the battery to self-discharge below an open-circuit voltage of 3.0 VPC will 

cause irreversible damage and void the warranty.

13. BATTERY MODULE FIRMWARE AND DATA LOGS

Always ensure the battery is using the latest firmware. AES Dashboard PC software 
is required to update the battery firmware and to download data logs from the 
battery. Get the latest software and battery operating firmware from the Discover 
Battery website at www.discoverbattery.com.

14. TROUBLESHOOTING

Accurate troubleshooting and warranty claims require data logs from each battery. 
Use AES Dashboard diagnostic software to download data logs one battery at a 
time.

Confirm you have the latest version of Dashboard, which was AES Dashboard  
7.0.6_win64 at the time of publishing. System owners are encouraged to install the 
AES Dashboard software on a laptop to troubleshoot their system.

15. RELATED INFORMATION

For warranty information, refer to 885-0046 Discover AES LiFePO

4

 Battery Warranty 

Policy, available from the Discover Battery website at www.discoverbattery.com.

16. GLOSSARY OF TERMS, ABBREVIATIONS, AND ACRONYMS

VPC 

Volts Per Cell

LFP

 

LiFePO

4

 Lithium Iron Phosphate

BMS 

Battery Management System

SOC

 

State of Charge

DOD

 

Depth of Discharge

 

Summary of Contents for Discover 42-48-6650





























Reviews: