background image

©2008 Nexxus Lighting, Inc.

LIMITED WARRANTY

Nexxus Lighting, Inc. warranties its products, excluding lamps, to be free from defects in material and/
or workmanship, under normal condition, use and service, for a period of two (2) years from the original 
invoice date (Five (5) Years for Red, Amber and Orange FlexLED and Border Light LED products and one 
(1) Year for Non-UL Listed Power Supplies). If proof of purchase is provided, Nexxus Lighting will war-
ranty the product for two (2) years from date of the purchase (Five (5) Years for Red, Amber and Orange 
FlexLED and Border Light products and one (1) Year for Non-UL Listed Power Supplies).

TERMS AND CONDITIONS:

This warranty only applies when Nexxus Lighting products are properly wired and installed together as 
a system; and operated within the electrical values shown on the Nexxus Lighting specification sheets; 
used in lighting equipment designed and approved for the application and environmental conditions 
(temperature, humidity) within the normal specified operating range of the system. This warranty does 
not apply to any abnormal use in violation of any applicable standard, code or instructions for use in 
installations including those contained in the latest National Electrical Code (NEC), the Standards for 
Safety of Underwriters Laboratory, Inc. (UL), Standards for the American National Standards Institute 
(ANSI), in Canada, the Canadian Standards Association (CSA), Europe (CE), Australia (C-Tick). This war-
ranty will not apply in the event of conditions demonstrating abnormal use or stress, including under/
over voltage conditions, excessive switching cycles, excessive operating hours, alterations, accident, 
theft, misuse, abuse and damaged caused by negligent installation, improper maintenance or where 
adequate care has not been taken to prevent damage to the lighting system. Replacement of Nexxus 
Lighting components with any other manufacturer will void the entire warranty. 

WARRANTY SERVICE CLAIMS:

Nexxus Lighting must issue a Return Material Authorization (RMA) number for all requests for warranty 
review. To expedite service, please contact Nexxus Lighting Customer Representative: 407-857-9900. 
If you are unsure whether a situation exists that is covered by this warranty, please contact Nexxus 
Lighting Customer Service for assistance. In the event of a defect in material or workmanship during 
the warranty period, Nexxus Lighting will repair or replace (at its own discretion) its products under the 
conditions of the warranty.

RETURN OF DEFECTIVE PRODUCT:

After contacting Nexxus Lighting, Inc. and receiving the RMA

#,

 the purchaser / user shall promptly re-

turn the product after receiving instructions regarding if, when and where to ship product. Product must 
be returned within 30 days of receiving RMA

#,

 Shipping box must be clearly marked with RMA

#.

 Failure 

to follow this procedure shall void this warranty. Nexxus Lighting will cover expenses for material but will 
not cover shipping costs. Products returned without an RMA

#

 will be refused and returned to sender at 

the senders expense.

REPLACEMENT OF PRODUCT, LIMITS OF LIABILITY:

The foregoing shall constitute the exclusive remedy of the purchaser and the sole liability of Nexxus 
Lighting, Inc. regarding its products and component warranty. NO WARRANTY OF MERCHANTABILITY 
OR FITNESS FOR A PARTICULAR PURPOSE IS MADE OR IS TO BE IMPLIED. In no event shall Nexxus 
Lighting, Inc. be liable for any other costs or damages including labor charges, lost profits or revenues, 
incidental, special or consequential damages. Total liability shall not exceed the total extended purchase 
price for the product.  Nexxus Lighting, Inc. reserves the right to examine all failed Nexxus Lighting, Inc. 
products and components to determine the cause of failure and patterns of usage and reserves the right 
to be the sole judge as to whether any product or component is defective and covered under this  
warranty.                                                                                           

MAN.ALS.LL100.V1.00

Summary of Contents for ALS-LLED-100











Reviews: