12
•
CAUTION: To avoid injury, avoid contact with roller “fingers” as they may be sharp.
•
CAUTION: Exercise care when adjusting or relocating the touch screen. Movement of the
touch screen could cause unexpected movement of the machine and injury to the operator.
•
CAUTION: If control or air pressure settings are set too high, higher noise levels may result
from increased part on part contact or part on machinery contact. Limit these settings and add
guards or covers to reduce airborne noise.
•
CAUTION: Exercise extreme care when clearing jams, replacing materials, changing controls
or mechanical settings, and cleaning internal parts. Be sure to de-energize energy sources
prior to removing guarding. Failure to do so may result in unexpected movement or flying
objects, which could cause crush, cut, or eye injuries.
•
CAUTION: Maintenance must be performed by specialized personnel. Qualified service
engineers must remove guards or covers to gain access to electrical or mechanical areas.
•
CAUTION: Maintenance must be performed regularly to ensure that the machine is operating
properly and to protect against injury. Routine maintenance includes: periodic inspections, the
replacement of worn or damaged components, the tightening of loose bolts or components, and
regular cleaning and adjustments. Contact APPI and/or service centers for service support if
there is not sufficient maintenance staff at your facility to perform regular maintenance.
Installation Procedures
The printer is transported completed assembled in a container designed to protect the machine during
shipment. If the printer is operating with the T-1000-S14, the printer will be bolted onto the bagger.
After removing the stretch wrapping, remove the carton from the skid, open the top and cut all four
corners using a safety knife. Then, transport the machine to the operating location.
CAUTION: Do not attempt to lift the machine from the carton without first cutting all sides open. To
prevent injury, do not attempt to lift the machine without assistance.
Operating Environment / Location
: The printer should be placed in an area free of excessive heat,
moisture, dirt, and dust. Operating room temperature should range from 50-100° Fahrenheit. (10-
37.7°Celcius)
Air and Power Requirements
Ti-1000Z
: Provision must be made for 110 VAC, 60 Hz line current with ground. Optional 220 VAC /
50 Hz voltage may have been supplied based on your local electrical requirements. The full load current
for the Ti-1000Z is 5 Amps.
NOTE: APPI recommends a dedicated 15 Amp circuit for the Ti-1000Z
CAUTION: A qualified electrician should ensure that the machine’s power outlet is properly
grounded, voltages are as required and amperage capacity is sufficient.
Ti-1000Z
: At least 0.5 CFM free air is required, regulated from 25 to 60 PSI (1.72 to 4.13 Bar), to obtain
the best print quality and drive roller compression.
Summary of Contents for Ti-1000ZR
