background image

1

Signal Word Definitions

DANGER indicates an imminently hazardous situation which, 

if not avoided, 

WILL

result in death or serious injury.

WARNING indicates a potentially hazardous situation which, 

if not avoided, 

COULD

result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, 

if not avoided, 

MAY

result in minor or moderate injury.

IMPORTANT indicates a potentially hazardous situation 

which, if not avoided, 

MAY

result in property damage.

1.0 Introduction

COOL-

SPACE

®

is a patented and registered Trade Mark of Advanced Radiant Systems, Inc.

and manufactured in Indiana.

The COOL-

SPACE

®

unit is a compact, self-contained, high-efficiency portable evaporative

cooler.

2.0 Unpacking your COOL-SPACE

®

unit

Carefully examine the carton for damage before opening. If the carton is damaged notify the 

shipping company immediately.

3.0 Set-up of the COOL-SPACE

®

unit

The COOL-

SPACE

®

unit is factory tested and ready to use. The unit should be placed on a

level surface, and the casters locked to prevent inadvertent movement. Follow instructions 

below to connect water and electrical supply.

3.1 Connecting the water supply

Do not connect the COOL-

SPACE

®

unit to any water source where water pressure exceeds 

120 psi. This will cause permanent damage to the unit.

The COOL-

SPACE

®

unit comes equipped with a female garden hose water source connection. 

Attach the unit to a standard garden hose outlet for a water source. It is not recommended that 

the unit be attached to any water source with operating pressures above 120 psi. If you have

not purchased the optional portable water tank; use a standard garden hose (not provided) to 

connect the tank to the cooler. 

Summary of Contents for CS5-16-VD-TB

















Reviews: