background image

 

 

* DO NOT dress cables over 

sharp edges that could cause 

wear or tearing of cable insulation. 
* DO NOT install components in locations where they might interfere with 
the vehicle operator or operating controls. 
* DO NOT install the Hands-free Cradle where it will be difficult for the 
operator to reach. 
 

! WARNING 

 
VEHICLES EQUIPPED WITH AIR BAGS 
An air bag inflates with great force. DO NOT place objects, including 
communications equipment, in the area over the air bag or in the air bag 
deployment area. If the communication equipment is improperly installed 
and the air bag inflates, this could cause serious injury. 
 
It is recommended that the installation of the vehicle communication 
equipment be performed by a professional installer/technician trained in 
the requirements for such installations. An air bag's size, shape and 
deployment area can vary by vehicle make, model, and front 
compartment configuration (for example, bench seat vs. bucket seats). 
Contact the vehicle manufacturer's corporate headquarters, if necessary, 
for specific air bag information for the vehicle make, model, and front 
compartment configuration involved in your communication equipment 
installation. 
 

! WARNING 

 
VEHICLES WITH ANTI-SKID BRAKING SYSTEMS 
For vehicles with electronic anti-skid braking systems, refer to the 
"Anti-Skid Braking Precautions," Motorola publication 68P81109E34. 
This publication can be ordered from Motorola® Worldwide Systems 
and Aftermarket Parts Department. 
 
Speaker Installation Detail Location 
1. Mount the Speaker beneath the dashboard, on the passenger's side 
of the vehicle out of the way of the passenger. 
2.  Do not mount the Speaker on the dashboard or the rear window 
shelf. 
3. The Speaker should be located more than four feet from the Car Kit 
Cradle. 
 
Installation Procedure 
1. The Speaker includes a mounting bracket, permitting it to be 
mounted in a variety of ways. Loosen the thumbscrews on the side of 
the speaker and using the mounting bracket as a template, drill the 
necessary mounting holes and secure the bracket with the self-tapping  
 
 

Summary of Contents for AT6538A









Reviews: